IMPULSE•VG+ Series 3 Instruction Manual – 07/25/05
5-66
39 External OH2
External Overheat Alarm
3A Trm A2/A3 Enable
Analog Inputs A2 and A3 are
Enabled
3D Fref UP Cmd
Used with B4-01
3E Fref Down Cmd
Used with B4-01
3F Fault Reset
Fault Reset; Normally Open
40 Fast Stop N.O.
Decel to Stop by B5-08
n/a
41 Motor 2 Switch
Motor 2 enabled
5-55
42 Fast Stop N.C.
Decel to Stop by B5-08
5-5
43 Timer Enable
Closed: enable ON-Delay/OFF
delay timer
5-40
45 + Speed Cmd
Trim Control Increase
46 — Speed Cmd
Trim Control Decrease
47 Analog Hold
Analog Frequency Reference
Hold
4C DCInj Activate
DC Injection Brake
50 Ext Spd Search 3
Micro-Speed Gain 1 and Load
Float extent.
53 Comm Test
Comm Loopback Test
55 Drive Enable
On = Inverter Ready
56 Klixon N.O.
Klixon Input; Normally Open
57 Klixon N.C.
Klixon Input; Normally Closed
58 Brake Answer back
Brake Answer Back
59 Alt F-Ref Up Lmt
Alternate Fre Ref Up Limit
5A Maintenance Reset
Reset Maintenance Timer
5-41
5B BE6 Up Speed Lmt
Limit Fref to C8-17
5C Weight Measure
Measure by C10-01
5-35
5D Load Float Ext
AMS C8-15 Time to C8-10
5E M-Spd Gni + LF-E
Micro Speed Gain and Load
Float Extend
5F Phantom Fault N.C.
Stop by C3-09
60 Index Enable
Enables index
5-43
61 Brake Test
See C8-19
5-31
62 Weight Limit N.O.
Upper Limit Stop; Normally
Open
63 Phantom Fault N.O.
Stop by C3-09
64 PG Ch1 Output
Switches PG output to Ch 1
65 Dwell Enable
Enables Dwell function
5-50
66 Load Share
Enables Load Share function
5-22
* Initial value is determined by X-Press Programming (Table 4.1 to 4.2).
Parameter
Code
Display
Function
Ref Page
Number
Содержание IMPULSE VG+ Series 3
