background image

 

Installation 

 

MultiView™ II DVI-Rx-1K 

Installation and User Guide 

Chapter 5 

Installation 

 
This section describes the following installation topics: 
 

 

Data mode configuration 

 

Prerequisites to installation 

 

Installation procedure 

 

Post-installation adjustments 

 

Post-installation configuration settings 

 

 

This equipment is not intended for, nor does it support, distribution through an Ethernet network.  
Do not connect these devices to any sort of networking or telecommunications equipment!   

 

 

Do not connect DC power until instructed to do so.

 

 

5.1 

Option-Module Configuration 

 
If you are installing a MVII-DVI-Rx-1K-

SAP

 version receiver (this is equipped with the SAP hardware option 

module), then the following information will be important to review BEFORE installing the receiver: 
 
The 

MVII-DVI-Rx-1K-SAP

 version offers pollable RS232 duplex serial in addition to true stereo audio. The 

serial interface is a 3-wire (TX, RX, GND) interface. The factory-default serial baud rate is 9600 baud, but this is 
a user-

configurable option using “SAP-II” serial commands. Simplex modes are supported without jumper or 

other changes by simply using the TX signal only. The serial-polling capability allows interaction with specific 
receivers. This will require that each receiver have a unique SAP-address setting. Please refer to Appendix-B 
for (SAP) module configuration information, and Appendix-C for SAP-address settings. 

5.2 

Prerequisites 

 
Depending on the specific installation requirements, some common tools (screwdrivers, nut-drivers) and related 
hardware (mounting screws) might be required. These are not provided with Magenta products. 
 
The following items might be necessary, which are available from Magenta Research: 
 

 

Audio cable: Phoenix 4-pin to RCA. 

 

Video cable: DVI (or HDMI with an appropriate DVI/HDMI adapter) 

 

Serial cable: Phoenix 4-pin to DB9, or one of several DB9-M/F, M/M or F/F extension cables. 

 

Note:

 You will need appropriate twisted-pair cable as previously described, to connect the MVII-DVI-Rx-1K to 

other 

MultiView™ II devices. tvONE does not supply this cable.

 

5.3 

Installation Procedure 

 

Ensure that all connectors are clean and free of contaminants prior to making the 
connections. Appropriate connector locking hardware (screws/latches) should be used to 
prevent cables from disconnecting or causing intermittent operation.  

All units must be the same type for 4

th

-pair supported features to function correctly. For 

example, a “MVII-DVI-Tx-A” must be paired with a MVII-DVI-Rx-1K-A, as both must be 
identical to work properly. Similarly, an 

“MVII-DVI-Tx-SAP” can only be used with an MVII-

DVI- Rx-1K-SAP

”. Video modes may function normally, but 4th pair options will not. 

 

Содержание MultiView II DVI-Rx-1K


































Отзывы: