background image

 

 

 

V2.0 – Jan-13 

User’s Manual 

Page 3 of 41

 

Disclaimer 

 
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF MAESTRO 
WIRELESS SOLUTIONS LIMITED. IT MAY NOT BE COPIED OR TRANSMITTED 
BY ANY MEANS, PASSED TO OTHERS, OR STORED IN ANY RETRIEVAL 
SYSTEM OR MEDIA, WITHOUT PRIOR CONSENT OF MAESTRO OR ITS 
AUTHORIZED AGENTS. 
 
THE INFORMATION IN THIS DOCUMENT IS, TO THE BEST OF OUR 
KNOWLEDGE, ENTIRELY CORRECT. HOWEVER, MAESTRO CAN NEITHER 
ACCEPT LIABILITY FOR ANY INACCURACIES, OR THE CONSEQUENCES 
THEREOF, NOR FOR ANY LIABILITY ARISING FROM THE USE OR 
APPLICATION OF ANY CIRCUIT, PRODUCT, OR EXAMPLE SHOWN IN THE 
DOCUMENT. 
 
THE PRODUCT (HARD- AND SOFTWARE) DESCRIBED IN THIS 
DOCUMENTATION IS NOT AUTHORIZED FOR USE IN LIFE SUPPORT DEVICES 
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF MAESTRO. 
 
THIS DOCUMENT MAY PROVIDE LINKS TO OTHER WORLD WIDE WEB SITES 
OR RESOURCES. BECAUSE MAESTRO HAS NO CONTROL OVER SUCH SITES 
AND RESOURCES, MAESTRO SHALL NOT BE RESPONSIBLE FOR THE 
AVAILABILITY OF SUCH EXTERNAL SITES OR RESOURCES, AND DOES NOT 
ENDORSE AND IS NOT RESPONSIBLE OR LIABLE FOR ANY CONTENT, 
ADVERTISING, PRODUCTS, OR OTHER MATERIALS ON OR AVAILABLE FROM 
SUCH SITES OR RESOURCES. MAESTRO SHALL NOT BE RESPONSIBLE OR 
LIABLE, DIRECTLY OR INDIRECTLY, FOR ANY DAMAGE OR LOSS CAUSED OR 
ALLEGED TO BE CAUSED BY OR IN CONNECTION WITH USE OF OR 
RELIANCE ON ANY SUCH CONTENT, GOODS OR SERVICES AVAILABLE ON 
OR THROUGH ANY SUCH SITE OR RESOURCE. 
 
MAESTRO RESERVES THE RIGHT TO CHANGE, MODIFY, OR IMPROVE THIS 
DOCUMENT OR THE PRODUCT DESCRIBED HEREIN, AS SEEN FIT BY 
MAESTRO WITHOUT FURTHER NOTICE. 
 

Содержание A2100-A/B










































Отзывы: