Macurco BRS-485 Скачать руководство пользователя

Страница: 24 / 33

Macurco MRS-485 Modbus RS-485 Adapter

REV – 1.0

[34-2900-0019-7]

P a g e

Maintenance

The BRS-485 does not require regular maintenance. All maintenance and repair of products manufactured by

Macurco are to be performed at the appropriate Macurco manufacturing facility. Macurco does not sanction

any third-party repair facilities.

WARNING

Do not disassemble unit or attempt to repair or modify any component of this instrument. This instrument

contains no user serviceable parts, and substitution of components may impair product performance and

void product warranty.

CAUTION

Avoid the use of harsh cleaning materials, abrasives, and other organic solvents. Such materials may
permanently scratch the surfaces and damage the LEDs, labels, or instrument housing.

7.1

Cleaning

Cleaning of the external surfaces is best carried out using a damp cloth with a mild detergent or soap. Use a

vacuum cleaner with soft brush to remove dust or contamination. Do not blow out the sensor with compressed
air.

Содержание BRS-485


































Результаты поиска

Содержание BRS-485

Отзывы:

Похожие инструкции для BRS-485

Бренды по названию

Популярные бренды

Macurco BRS-485, Инструкция пользователя

Результаты поиска

Содержание BRS-485

Отзывы:

Похожие инструкции для BRS-485

Бренды по названию

Популярные бренды