Macurco BRS-485 Скачать руководство пользователя | Manualshive

Страница: 16 / 33

background image

Macurco MRS-485 Modbus RS-485 Adapter

REV – 1.0

[34-2900-0019-7]

15

|

P a g e

4.1

Macurco NPU Software

Macurco Network Parameter Utility software can be used to set the BRS-485 to desired address, change the

communication protocol and communication settings. This software can also be used to update BRS-485 with

any latest firmware release from Macurco. Figure 4.1 shows the screen of NPU software when a device is

connected. As shown in the Figure, it displays the device name (BRS-485) with device configuration version
(V1.0DS) under it. Fields greyed out are read-only.

Protocol- Factory default for this field is BACnet. Click on drop down list to select appropriate communication
protocol. Modbus, BACnet, Metasys and Siemens are protocol supported by BRS-485.

Address - The address of the device in the network. This setting is not available for BACnet.

MAC Address: Defines the address (0-127) that the BRS-485 (node) will reside on the network. This setting is
available for BACnet only.

Baud Rate - Baud rate of the network.

Parity - Parity for the communication.

Response Delay: Time in milliseconds that the driver waits before responding to master requests. If no delay is

required, setting this field to 0 instructs the driver to send its response as soon as possible. This setting is not
available for BACnet.

APDU Timeout - The time in milliseconds that the driver will wait for a response from a device after sending a
request. This setting is available for BACnet only.

A number of APDU Retries - The number of times the driver will retry a request when a response is not received.
This setting is available for BACnet only.

«
...
14
15
16
17
18
...
»

Содержание BRS-485


































Отзывы:

Нет отзывов

Похожие инструкции для BRS-485

Бренд: j5 create Страницы: 444

Бренд: Warpia Страницы: 28

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: TEXIO Страницы: 49

Бренд: ZyXEL Communications Страницы: 2

Бренд: 3idee Страницы: 5

Бренд: Uconnect Страницы: 8

Бренд: cable matters Страницы: 12

Бренд: i-tec Страницы: 32

Бренд: Davis Instruments Страницы: 4

Бренд: Lindy Страницы: 2

Бренд: Yealink Страницы: 8

Бренд: Devolo Страницы: 16

Бренд: Sabrent Страницы: 4

10/100/1000 Base-T Ethernet PCI

Бренд: IBM Страницы: 38

Бренд: RODE Microphones Страницы: 3

Бренд: Fein Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды