Mackie U.40d страница 7 Скачать руководство пользователя

Страница: 7 / 32

Owner’s Manual

Owner’

s Manual

Music Production Studio 2

GND

PHONO

LINE

MIC/LINE

OUT

MAIN

OUT

AUX

(MONO)

POWER

18V,1.5A

Headphones

ground wire

Turntable with phono-level output

Laptop

HR824

Powered

Monitors

Acoustic Guitar

and mic

USB

Keyboard

Controller

Studio

Vocal

Mic

Synth workstation

Drum

Machine

This diagram shows an acoustic guitar microphone attached to channel 1’s XLR input, a vocal condens-

er microphone connected to channel 2’s XLR input, two turntables are connected to channel 3 and 4’s

phono inputs, and a drum machine and keyboard workstation are attached to their line inputs.

Note: Each turntable is disconnected whenever a 1/4” plug is inserted into a line input on the same

channel, so physically pull out the 1/4” plug whenever you want to play a record.

The main outputs are fed to a pair of Mackie HR studio monitors for control room listening, and the

mixer’s Big Knob controls their volume. The headphone out has its own level control independent of the

Big Knob.

A laptop is connected via FireWire. The mixer provides stereo mains to the computer for recording with

most DAW applications like Tracktion, Cubase, or Logic. This is independent of the Big Knob as well. The

laptop is loaded with awesome virtual instruments like those in applications such as Logic, and a USB

key/pads combo controller is connected for real-time performance and recording.

The FireWire loop through switch on the top of the mixer makes overdubbing a breeze. In it’s normal

out position, you can play back the mix from your DAW and it will not loop back through the FireWire.

Only the analog inputs 1-4 will be available for recording. Track it!

Содержание U.40d

































Результаты поиска

Содержание U.40d

Отзывы:

Похожие инструкции для U.40d

Бренды по названию

Популярные бренды

Mackie U.40d, Руководство пользователя

Результаты поиска

Содержание U.40d

Отзывы:

Похожие инструкции для U.40d

Бренды по названию

Популярные бренды