background image

Speedplay

, Inc.

10151 Pacific Mesa Blvd., #107

San Diego, Ca 92121 (858) 453-4707 1-800-468-6694   www

.speedplay

.com

Hand Over Instructions T

o Customer

Please V

isit www

.speedplay

.com For 

Instructions In 

Additional Languages.

IMPOR

TANT

Failure T

o Follow These Instructions 

And 

 W

arning Statements Before 

Assembling 

And Using 

This System May Result In Serious Personal Injury

.

SPEEDPLA

Y

®

 

ZERO AERO 

PED

AL SYSTEM

Zero Aero Pedal Disassembly

Tools Needed: T-20 Torx Key, Retainer clip pliers, 15mm open-end wrench, Pick tool.

Step 1. Use a Pick Tool to pry out the Dust Cap.

Step 2. Remove the Torx Screw (T-20 size) from the end of the spindle. To ease removal of the Torx 

Screw, heat the screw with a soldering gun to 300°F to loosen the bond of the Loctite on the 

screw threads.

Step 3. Pull the spindle out of the Zero Aero Pedal body.

Step 4. Using retainer clip pliers, remove the retainer clip from the groove in the bore of the Pedal body.

Step 5. Push the two cartridge bearings out the dust cap side of the Pedal body. (Use the spindle with 

Torx Screw partially installed as a tool to carefully push the bearings out of the Pedal body).

NOTE: Do not try to remove the needle bearing from the Zero Aero Pedal body. The needle bearing 

is permanently bonded in the Zero Aero Pedal body and cannot be removed without damaging 

components.

Lubrication and Reassembly

Use a high-quality, waterproof grease on the needle bearing and use a new “O“ ring (grease it too) when

overhauling Zero Aero Pedals. Any worn or damaged parts should be replaced. Reassembly is

accomplished by reversing the order of the above instructions. 

Be sure retainer clip is fully seated in

bore groove and reapply Loctite to the Torx Screw threads when reassembling Pedal.

 

     Tighten T-20 Spindle-End Screw Securely (3.6 Nm / 32 inch pounds).

 

     Tighten T-15 Bowtie Screws Securely (4.5 Nm / 40 inch pounds).

*

Included with the Zero Aero Pedal System

NOTE: Do not try to remove the needle bearing from the Zero Aero Pedal body. The needle

bearing is permanently bonded in the Zero Aero Pedal body and cannot be removed without 

damaging components.

                 Use Grease Only! Never use oil or spray lubes on bearings.

1. Use a pick tool to pry out the Dust Cap.

2. Insert the Aero Pedal Luber into the Pedal Body.

3. Gently tap in the Aero Pedal Luber.

4. Insert needle-type grease injector gun into Aero Pedal Luber grease port hole.

5. Pump gun slowly while turning Zero Aero Pedal body slowly until clean grease is visible at spindle       

 end of Pedal Body.

6. Remove the Aero Pedal Luber using pliers and wipe off the excess grease.  

7. Insert the Dust Cap back into the body.  

NOTE: Make sure the Dust Cap is inserted in the same orientation it was removed in.                

The aero profile must match between the Pedal Body and the Dust Cap.  

NOTE: Damage due to the lack of lubrication is not covered by Speedplay’s warranty policy. 

Speedplay recommends that the Zero Aero Pedal bearings be greased with a pump-type grease 

gun at least every 2000 miles or every three months. Pedals should always be lubricated imme

-

diately after riding in wet, rainy or unusually dusty conditions. 

Speedplay Grease Guns (Part # 

13175) and replacement 3oz. Grease Tube (Part # 13560) are available from Speedplay retailers or call 

Speedplay at 1-800-468-6694 (PST). `

LIMITED (TWO YEAR) WARRANTY

This Speedplay product is warranted under normal usage against 

defects in workmanship and materials to the original purchaser for 

a period of two (2) years from the date of purchase free of charge 

provided the claim is made within thirty (30) days of the discovery 

of the defect and the following condition is met: The purchaser must 

obtain advance authorization by calling Speedplay at 800-468-6694 

toll free or (858) 453-4707 before returning any product for warranty 

inspection. A Return Authorization (RA) number will be issued and 

must conspicuously appear on the outside of the product's 

packaging. The issuance of an RA number does not constitute 

acceptance of the claim. The determination of whether the claim is covered by this warranty is within the 

sole discretion of Speedplay, Inc. The part(s) requiring service or replacement must be returned to 

Speedplay, either by the purchaser or a Speedplay dealer.  Insurance, handling and transportation 

charges for service shall be borne by the person desiring service. This warranty is limited to the repair 

or replacement of this product.  Speedplay, at its option, will either repair or replace any defective parts.

For a warranty claim to be honored, the following information  must accompany the returned product:

a) A copy of the original dated receipt or other proof of retail purchase.

b) A detailed description of the problem with the product along with the R.A. number.

c) Identification of the shoe brand and model used in conjunction with the product.

d) Estimate of product usage (in accumulated mileage).

e) Your name, street address (no P.O. boxes) and phone number(s) where you may be reached.

f) The product must be securely packaged and sent insured through a traceable shipper.

The repaired product or replacement will be returned to the purchaser or the Speedplay dealer usually 

within two weeks.  Product furnished as replacement will continue to be covered under this warranty until 

two years after the date of original purchase.

Limits and exclusions: Not covered by warranty is damage resulting from normal wear and deterioration 

occurring from use, accidents, neglect, improper assembly, misuse, abuse, lack of reasonable or proper 

maintenance, corrosion, any damage resulting from causes other than defects in materials and workman-

ship; failure or loss by accident, alterations, repairs improperly performed, or replacement parts improper-

ly installed, modifications not recommended or approved in writing by Speedplay, labor costs for removal, 

or compensation for inconvenience or loss of use while the product is being repaired or replaced. This 

warranty also does not cover cosmetic imperfections in the surface finish, or appearance of the product 

which were apparent or discoverable at the time of purchase, or damage during shipment of the product.

There are no warranties which extend beyond the face hereof. All warranties implied by state law, includ-

ing the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to 

the duration of the limited warranty set forth above. Some states do not allow limitations on how long an 

implied warranty lasts, so the above limitation may not apply to you. With the exception of any warranties 

implied by state law as hereby limited, the foregoing express limited warranty is exclusive and in lieu of all 

other warranties, guarantees, agreements and similar obligations of manufacturer or seller. Speedplay is 

not liable for indirect or consequential damages in connection with the use of this product.  Some states 

do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or 

exclusion may not apply to you.

No person, independent representative, agent, distributor, dealer (including any Speedplay dealer) or 

company is authorized to change, modify or extend the terms of this warranty in any manner whatsoever. 

This warranty gives you specific legal rights; you may also have other rights which vary from state to state.

CAUTION

WITH ZERO AERO W

ALKABLE™ CLEA

TS

Dust

Cap

Spindle

Screw

Retaining

Ring

136 

Bearing

137 

Bearing

Zero Aero

Pedal Body

Needle 

Bearing

O-Ring

Spindle *

* Pedals with Titanium spindles 

have a rider weight limit of 185 

pounds. 

WARNING

!

WARNING

!

®

Aero Pedal Luber 

Dust Cap

Instructions for Quick and Easy Pedal Bearing Lubrication Using the Aero Pedal Luber*

Содержание Luber ZERO AERO

Страница 1: ... any product for warranty inspection A Return Authorization RA number will be issued and must conspicuously appear on the outside of the product s packaging The issuance of an RA number does not constitute acceptance of the claim The determination of whether the claim is covered by this warranty is within the sole discretion of Speedplay Inc The part s requiring service or replacement must be retu...

Страница 2: ...n quickly place your foot on the ground at any time Speedplay Pedals are not designed to release automatically at times such as when falling off the bicycle This is a safe ty measure to prevent you from losing balance and falling off the bicycle as a result of your feet becoming accidentally released from the Pedals Do not attempt to engage Speedplay Zero Aero Walkable Cleats onto Speedplay X Peda...

Страница 3: ...t directly against the shoe sole Shoes with a 4 Hole pattern do not accommodate the use of Aero Surrounds because there is no gap to cover Shoe Soles with a 4 Hole pattern These shoes require the Speedplay Walkable Cleat Protector Shim Kit Part 14135 sold separately to be installed between the Spring Housing and the shoe sole If the Walkable Cleat Protector Shim Kit is not used serious wear damage...

Страница 4: ... ride with the Zero Aero Pedal System separately engage the LEFT shoe with Cleat onto the LEFT Pedal and the RIGHT shoe with Cleat onto the RIGHT Pedal When the Zero Aero Walkable Cleats are mounted correctly the Zero Aero Pedal should float in the Zero Aero Walk able Cleat with little resistance and should emit a crisp audible snap when the cleat springs engage the grooves of the pedals Speedplay...

Отзывы: