MacDon MD 259140 Скачать руководство пользователя страница 3

Страница: 3 / 34

Introduction

The Small Drum kit (MD #259140) can be installed on a MacDon R116 Rotary Disc Pull-Type (model years 2015

–

2017) to

improve cutting performance in certain conditions. The kit contains two drums and associated parts to replace the factory-
installed inner drums on the pull-type.

This document explains how to install the kit. A list of parts included in the kit is provided in Chapter

2 Parts List, page 5

Installation time

Installation time for this kit is approximately 2.5 hours.

Conventions

The following conventions are used in this document:

•

Right and left are determined from the operator

’

s position. The front of the pull-type is the side that faces the crop.

•

Unless otherwise noted, use the standard torque values provided in the pull-type operator

’

s manual and technical

manual.

NOTE:

Keep your MacDon publications up-to-date. The most current version of this instruction can be downloaded from our
Dealer-only site (

https://portal.macdon.com

) (login required).

NOTE:

This document is currently available in English only.

214913

Revision B

Содержание MD 259140



































Результаты поиска

Содержание MD 259140

Отзывы:

Похожие инструкции для MD 259140

Бренды по названию

Популярные бренды

MacDon MD 259140, Руководство по установке

Результаты поиска

Содержание MD 259140

Отзывы:

Похожие инструкции для MD 259140

Бренды по названию

Популярные бренды