MacDon C Series Скачать руководство пользователя страница 3

Страница: 3 / 17

MacDon Industries Ltd.

680 Moray Street, Winnipeg, Manitoba, Canada R3J 3S3
T. (204) 885-5590 f. (204) 895-9146 www.macdon.com

215037

Revision B

U&A, Dealer

– C Series

Safety

1.1 Signal Words

Three signal words,

DANGER, WARNING,

and

CAUTION,

are used to alert you to hazardous situations. Two signal words,

IMPORTANT

and

NOTE,

identify non-safety related information. Signal words are selected using the following guidelines:

DANGER

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. It may also be

used to alert against unsafe practices.

CAUTION

Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may be used

to alert against unsafe practices.

IMPORTANT:

Indicates a situation that, if not avoided, could result in a malfunction or damage to the machine.

NOTE:

Provides additional information or advice.

Содержание C Series


















Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды

MacDon C Series, Инструкции по разгрузке и сборке

Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды