Mac allister SOLO MLM3637-Li Скачать руководство пользователя

Страница: 30 / 40

detail...

MLM3637-Li

by MacAllister

Care and maintenance

Underbody and cutting blade

1. Keep the underbody and cutting blade (12d) clean and free of debris. Remove

clippings from the rear discharge chute (20).

2. Check all fasteners, such as nuts and bolts, periodically for tightness before

operation. After prolonged use, especially in sandy soil conditions, the cutting

blade will become worn and lose some of the original shape. The cutting

efficiency will be reduced and the cutting blade should be replaced.

3. Keep the cutting blade (12d) sharp to

ensure a good cutting performance.

Replace a worn or damaged cutting

blade with a new one of the same

type or have it sharpened by a

qualified specialist.

4. Loosen the hex nut (12e) anticlockwise

using a suitable wrench

(Size 17 mm) and remove it together

with the cutting blade (12d) (Fig. 21).

5. Replace the cutting blade (12d) with a new one of the same type. Check the

status of flange (12c), the bushing (12b) onto the spindle (12a) firstly, then

attach the cutting blade (12d) and hex nut (12e) properly. Tighten the hex nut

(12e) clockwise with 20 Nm min, 25 Nm max. to ensure safe operation of your

product.

6. Replace this cutting blade after 50 hours mowing or 2 years whichever is

sooner regardless of condition. If the cutting blade is cracked or damaged,

you must immediately replace it with a new one.

7. Lubricate the cutting blade (12d) after each use to prolong the life span of

cutting blade and product. Apply light machine oil along the edge of the

cutting blade.

WARNING!

Wear safety gloves when working on the blade and close

to it! Use proper tools to remove debris, e. g. a wooden stick! Never

use your bare hands!

Always use original spare parts for replacement. The cutting blade

must be replaced by an identification no. ref. A056018200. Do not

attach any other type of cutting blade!

The replacement of the cutting blade should be done by a qualified

specialist! Rework or sharpening blades is not recommended unless

it is done by a repair service or a similarly qualified specialist!

Wear safety gloves when working on the blade and close

12e

12d

12c

12b

12a

Fig. 21

Содержание SOLO MLM3637-Li









































Результаты поиска

Содержание SOLO MLM3637-Li

Отзывы:

Похожие инструкции для SOLO MLM3637-Li

Бренды по названию

Популярные бренды

Mac allister SOLO MLM3637-Li, Руководство пользователя

Результаты поиска

Содержание SOLO MLM3637-Li

Отзывы:

Похожие инструкции для SOLO MLM3637-Li

Бренды по названию

Популярные бренды