Maaselan Kone Oy Hakki Pilke 37 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 57

background image

24

Original

Version 1-2011

4.3 Adjusting the log length and the height of the splitting

blade

The Hakki Pilke 1X37 is equipped with a mechanical log measurement device with an incremented
adjustment range of 20–60 cm.

5. Set the splitting blade to the desired height according to log size by using the adjustment lever.

NOTE! When the wood diameter exceeds 30 cm, turn the limiter!

Note!

The splitting blade can

also be removed.

1. Lower the blade with the
adjustment lever.

2. Lift the blade out.

3. Re-install the blade in the
reverse order.

1.  To  adjust  the  length  of  the  wood  to  be  cut,  set  the
operating lever C (Figure 19) to the Stop position, which
enables you to open the guard of the splitting blade.
2. When the wood limiter is in splitting position, set it to
the  desired  length  by  removing  the  cotter  pin  in  the
limiter's  locking  pin  and  by  pulling  out  the  locking  pin.
Lock the plate in the desired position.
Re-insert the locking pin and cotter pin.
3. Lower the splitter guard and turn the operating lever C
back to the Run position.

Small logs

Large logs

4. Check that the splitting
beam is in the initial
position and not extended
towards the splitting
blade.

«
...
22
23
24
25
26
...
»

Содержание Hakki Pilke 37 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для Hakki Pilke 37 Series

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 5

Бренд: Sealey Страницы: 8

Бренд: GÜDE Страницы: 76

Бренд: Wallenstein Страницы: 18

Бренд: Woodstar Страницы: 60

AGRI EASE BE-LS22TL6505GC

Бренд: BE Ag & Industrial Страницы: 40

Бренд: BW Machinery Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды