Maaselan Kone Oy Hakki Pilke 37 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 57

background image

18

Original

Version 1-2011

NOTE!

DO NOT PASS UNDER THE CONVEYOR!

6. Extend the conveyor to its full length.

7. Use the winch to adjust the conveyor to the
desired inclination, and lock the extension
with the lock at the bottom of the conveyor
and with a ring pin.

CHECK THE CONDITION OF THE CONVEYOR WINCH AND ITS COMPONENTS ON A DAILY BASIS. IF
YOU DISCOVER A FAULT, NO MATTER HOW SMALL, REPLACE THEM.

8. Turn the belt support to the side of the conveyor.

5. Lift the conveyor extension by the handle.

«
...
16
17
18
19
20
...
»

Содержание Hakki Pilke 37 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для Hakki Pilke 37 Series

Power Split 540H

Бренд: Texas Страницы: 50

Power Split 550H

Бренд: Texas Страницы: 64

Бренд: Texas Страницы: 64

Бренд: The Handy Страницы: 8

Бренд: The Handy Страницы: 12

Бренд: The Handy Страницы: 13

Бренд: The Handy Страницы: 24

Бренд: Woodstar Страницы: 68

Бренд: Lumag Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды