Maaselan Kone Oy Hakki Pilke 37 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 57

background image

16

Original

Version 1-2011

Note! Inspect and clean the machine according to Sections 2.1 and 9.0 before arranging it for transport.

3.2

Placing the input conveyor in the operating or transport

position

3.3 Placing the output conveyor in the operating position

TO PLACE THE CONVEYOR IN THE TRANSPORT POSITION, REVERSE THE ORDER OF THE
MEASURES COMPLETED TO PALCE THE MACHINE IN THE OPERATING POSITION!

REMEMBER THAT THE LOCKING HANDLE LOCKS THE SUPPORT IN PLACE!

1. Remove the split pin
from the locking handle.

2. Remove the
locking handle
from the
support.

3. Lower the conveyor to a
horizontal position, and
insert the conveyor support
in the slots in the lower
section of the machine's
frame.

Locking handle

Retain the split pin of the locking handle and the locking handle of the support.

«
...
14
15
16
17
18
...
»

Содержание Hakki Pilke 37 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для Hakki Pilke 37 Series

Бренд: MTD Страницы: 16

Бренд: North Star Страницы: 46

Бренд: Scheppach Страницы: 52

Бренд: Forest-Master Страницы: 24

Бренд: Tracmaster Страницы: 24

Бренд: SBI Страницы: 16

Бренд: Rok Страницы: 16

1600001-2000000

Бренд: Mountfield Страницы: 44

Бренд: FISCH Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды