Maaselan Kone Oy Hakki Pilke 37 Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 57

background image

20

Original

Version 1-2011

4.0

Control devices

The control devices of the Hakki Pilke 1X37 log splitter (basic model) are presented in Figure 19. The
names and functions of the control devices are as follows:

A.

Operating lever for the cutting flange, which also controls the feed motion of the input
conveyor

B.

Wood press handle

C.

Operating lever for the splitting mechanism (manual control)

D.

Control valve for an auxiliary device (accessory)

E.

Reverse pedal for the input conveyor

F.

Running speed adjuster for the output conveyor (in machines with a pivoting output
conveyor)

G.

Startup pedal for the splitting mechanism (manual control)

H.

Height adjustment lever for the splitting blade

Figure 19. The control devices of the machine (basic model)

A

B

C

D

E

F

G

H

«
...
18
19
20
21
22
...
»

Содержание Hakki Pilke 37 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для Hakki Pilke 37 Series

Бренд: Yard-Man Страницы: 16

Бренд: DK2 Power Страницы: 72

Бренд: The Handy Страницы: 24

Бренд: Wallenstein Страницы: 45

Бренд: sunjoe Страницы: 24

Бренд: MTD Страницы: 12

Бренд: MTD Страницы: 15

Бренд: MTD Страницы: 16

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 20

Бренд: Könner & Söhnen Страницы: 15

Бренд: Ariens Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды