M1 Drones M1 STEM Drone Series Скачать руководство пользователя | Manualshive

Страница: 43 / 45

background image

Warranty and Service Contact Information

Country of

Purchase

M1 Vision

Contact Information

Address

United States

of America

M1 DRONES Service Center

(Repairs and Repair Requests)

[email protected]

317-537-7644

PO Box 36851

Indianapolis, IN. 46236

M1 DRONES Product Support

(Product Technical Assistance)

[email protected]

Sales

[email protected]

317-537-7644

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject  to the following  two conditions:  (1) This
device may not cause harmful interference, and (2) this device must accept any interference  received,
including interference  that may cause undesired operation.

CAUTION:

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be
compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz
frequency range.

43

«
...
41
42
43
44
45
»

Содержание M1 STEM Drone Series














































Отзывы:

Нет отзывов

Похожие инструкции для M1 STEM Drone Series

Бренд: YUNEEC Страницы: 37

Super Hornet X650

Бренд: TTRobotix Страницы: 14

Бренд: Eachine Страницы: 11

Бренд: Holy Stone Страницы: 30

Бренд: Alpha Страницы: 14

Бренд: Velleman Страницы: 83

BEBOP 2 FPV Pack

Бренд: Parrot Страницы: 259

Бренд: Hangzhou Qifei Intelligence Technology Страницы: 52

Бренд: Ugo Страницы: 18

Бренд: Xiaomi Страницы: 14

Бренд: Elan Страницы: 26

Бренд: Neheme Страницы: 8

Бренд: Parallax Страницы: 5

Бренд: Jamara Страницы: 16

Бренд: Walkera Страницы: 20

Бренд: UDI R/C Страницы: 16

Бренд: Dragon Touch Страницы: 50

Micro Quadrocopter II

Бренд: Carrera RC Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды