background image

Limited Warranty

What this Warranty Covers

M1   DRONES,   LLC,   (M1)   warrants   to   the   original

purchaser that the product purchased (the "Product") will

be free from defects in materials and workmanship at the

date of purchase 

What is Not Covered

This warranty is not transferable and does not cover (i)
cosmetic   damage,   (ii)   damage   due   to   acts   of   God,
accident, misuse, abuse, negligence, commercial use, or
due   to   improper   use,   installation,   operation   or
maintenance,  (iii)   modification  of  or  to   any  part  of  the
Product,   (iv)   service   attempted,   outside   manufacturer
specifications,   by   anyone   other   than   a   M1   Vision
authorized service center, (v) Product not purchased from
an authorized M1 dealer, or
(vi)   Product   not   compliant   with   applicable   technical
regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, M1
MAKES   NO   OTHER   WARRANTY   OR
REPRESENTATION,   AND   HEREBY   DISCLAIMS   ANY
AND   ALL   IMPLIED   WARRANTIES,   INCLUDING,
WITHOUT   LIMITATION,   THE   IMPLIED   WARRANTIES
OF   NON-INFRINGEMENT,   MERCHANTABILITY   AND
FITNESS   FOR   A   PARTICULAR   PURPOSE.   THE
PURCHASER   ACKNOWLEDGES   THAT  THEY   ALONE
HAVE   DETERMINED   THAT   THE   PRODUCT   WILL
SUITABLY   MEET   THE   REQUIREMENTS   OF   THE
PURCHASER’S INTENDED USE.

Purchaser’s Remedy

M1’s sole obligation and purchaser’s sole and exclusive
remedy   shall   be   that   M1   will,   at   its   option,   either   (i)
service, or (ii) replace, any Product determined by M1 to
be defective. M1 reserves the right to inspect any and all
Product(s)   involved   in   a   warranty   claim.   Service   or
replacement decisions are at the sole discretion of M1.
Proof of purchase is required for all warranty claims.  

SERVICE   OR   REPLACEMENT   AS   PROVIDED
UNDER   THIS   WARRANTY   IS   THE
PURCHASER’S   SOLE   AND   EXCLUSIVE
REMEDY.

Limitation of Liability

M1 SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS
OF   PROFITS   OR   PRODUCTION   OR   COMMERCIAL
LOSS   IN   ANY   WAY,   REGARDLESS   OF   WHETHER
SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
TORT,   NEGLIGENCE,   STRICT   LIABILITY   OR   ANY
OTHER THEORY OF LIABILITY, EVEN IF M1 HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of M1 exceed the
individual   price   of   the   Product   on   which   liability   is
asserted.   As   M1   has   no  control   over   use,   setup,   final
assembly,   modification   or   misuse,   no   liability   shall   be
assumed nor accepted for any resulting damage or injury.
By the act of use, setup or assembly, the user accepts all
resulting liability. If you as the purchaser or user are not
prepared to accept the liability associated with the use of
the Product, purchaser is advised to return the Product
immediately in new and unused condition to the place of
purchase.

Law

These terms are governed by Florida law (without regard
to   conflict   of   law   principals).     This   warranty   gives   you
specific legal rights, and you may also have other rights
which vary from state to state.   M1 reserves the right to
change or modify this warranty at any time without notice.

41

Содержание M1 STEM Drone Series














































Отзывы: