background image

Premier 4-6-0 Camelback Steam Locomotive

10

®

Proto-Sound 2.0 Operating Instructions

This manual contains the operating instructions for Proto-Sound 2.0 in 
conventional mode only.  Instructions for accessing DCS command mode features 
accompany the DCS Remote Control System equipment.

Activating Proto-Sound 2.0 Conventional 

Mode Features

Proto-Sound 2.0 features are activated by sequences of Bell a nd Horn button 
pushes described below.  Please read the full descriptions of  each feature before 
using it. To use these buttons to activate features rather than to blow the horn or 
ring the bell, you should tap the buttons very quickly with a ½-second pause 
between button presses.  You may need to practice your timing to make this work 
smoothly.

Feature to Be Activated

Button Code:

Freight Yard or Passenger Station Sounds
Fire the Rear Coupler
Fire the Front Coupler
Speed Control On/Off
Lock into a Direction
Reset to Factory Defaults

1 Bell, 2 Horn/Whistles
1 Bell, 3 Horn/Whistles
1 Bell, 4 Horn/Whistles
1 Horn/Whistle, 2 Bells (from Neutral only)
1 Horn/Whistle, 3 Bells
1 Horn/Whistle, 5 Bells (from Neutral only)

Timing Chart

Total Time Lapse: 1

Seconds

½

Press

Whistle

Short & 

Firm

½ Sec.

Pause

½ Sec.

Pause

Press

Bell

Short & 

Firm

Press

Bell

Short & 

Firm

Содержание Premier 4-6-0 Camelback Steam Locomotive





























Отзывы: