M-system M3LU Скачать руководство пользователя

Страница: 9 / 9

M3LU

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]

EM-2652-A Rev.2 P. 9 / 9

STATUS INDICATOR LED

Combinations of the three front LEDs (LD1, LD2, LD3) in-
dicate the transmitter’s operating status by different blink-
ing patterns.
Examples are shown below.

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

NORMAL OPERATION (RUN) MODE

ERROR MODE

System Error

Indicates the CPU’s communication error.

DIP SW Error

DIP SW configuration is inappropriate.
Check the DIP SW setting referring to Tables 2 – 11.

Burnout in PC Configuration Mode (Option A)

Burnout in DIP SW Configuration Mode

PC Configuration RUN Mode (Option A)

The transmitter is configured via PC and
is in normal operating conditions.

DIP SW Configuration RUN Mode

The transmitter is configured via DIP SW and
is in normal operating conditions.

Output Saturated in PC Configuration Mode
(Option A)

The output is below -15% or above 115%.

Output Saturated in DIP SW Configuration Mode

The output is below -15% or above 115%.

Amber LED

Green LED

Red LED

OFF

Blink

Содержание M3LU










Результаты поиска

Содержание M3LU

Отзывы:

Похожие инструкции для M3LU

Бренды по названию

Популярные бренды

M-system M3LU, Инструкция по эксплуатации

Результаты поиска

Содержание M3LU

Отзывы:

Похожие инструкции для M3LU

Бренды по названию

Популярные бренды