background image

LX900 PROGRAMMING AND OPERATION

LDT, LDTB

11

MODES OF OPERATION

This controller has three (3) different modes of operation B2, C2, and TS (Timer Secure).  Factory default is B2 mode and 

the Timer To Close (TTC) is 0 seconds. Anytime the operator does not detect safety beams, it will automatically change to 

C2 mode. If the TTC is larger than 0 seconds, it will automatically change to TS mode.  There are 7 fixed delays for TTC – 

3, 15, 30, 45, 60, 90 and 180 seconds. To adjust the setting, hold in the TTC button (refer to diagram). Three LED's above 

the TTC button will indicate the current setting on the adjacent chart. After reaching 180 seconds, it will jump back to 0 

seconds (default) and the operator will revert to B2 Mode.  

C2 Mode

•  Momentary press of OPEN will open door.

•  Constant pressure required on CLOSE for the door to close. 

•  Single or three button transmitter will open or stop the door only.

B2 Mode

•  Momentary press of OPEN or CLOSE will activate door.

•  Single button - reverses a closing door, stops an opening door.

•  Transmitters activate operator same as wall stations.

TS Mode

•  Button function is the same as B2 mode.

•  Includes Timer to Close (TTC) function. The door will automatically close after set time expires.  Timer starts when 

door reaches the open limit. (When first entering TS mode or after power interruption, momentary press of OPEN will 

start timer if door is at OPEN limit.)

General Notes regarding Mode of Operations:

•  After power interruption the first  move is Open.

•  STOP button works in all modes of operation. If the 3 button wall station is not connected to the Control board or there 

is no jumper between COM and STOP, the motor will not run.

•  The Constant Pressure (CP) feature will work only from 3 and 1 button wired Wall Stations

•  The controller includes a Run Timer: a maximum amount of time the motor will run after receiving either open or close 

command. Factory default: 45 seconds. Not adjustable.

•  Open override means that the door may be reversed while closing by activating an OPEN button without the need to 

use the STOP button first (for all 3 Modes).

To reduce the risk of serious injury or death, follow these instructions carefully: 

•  Read and follow ALL instructions.

•  Keep fingers and other body parts away from all moving parts of the door and gate operator system 

while it is being operated.

•  Keep the radio controls away from children. Do not allow children to play with the controls.

•  Keep away from the door when it is in motion. Watch the door while it is moving until completely 

closed or opened.

•  Do not cross the path of a moving door.

•  Disable and locks and remove any ropes connected to the garage door to avoid entanglement and 

prevent damage to the system.

•  Do not make repairs to cable, springs, or other hardware; call a trained door systems technician. The system is 

under extreme tension and can cause serious injury or death.

•  Ensure that the door is properly operating and balanced. If not, call a trained door systems technician to make 

repairs.

WARNING

Содержание Napoleon Lynx LDT


















Отзывы: