Lycoming TIO-540-A1A Скачать руководство пользователя страница 121

Страница: 121 / 138

LYCOMING OPERATOR’S MANUAL

SECTION 6

TIO-540 SERIES – ANGLE VALVE CYLINDER HEADS

TROUBLE-SHOOTING

TROUBLE

PROBABLE CAUSE

REMEDY

Low Power and Uneven

Defective ignition wire

Check wire with electric tester.

Running (Cont.)

Replace defective wire.

Defective spark plug terminal

Replace connectors on spark

connectors

plug wire.

Plugged fuel injector nozzle

Clean or replace nozzle.

Failure of Engine to Develop

Leak in induction system

Tighten all connections and

Full Power

replace defective parts.

Plugged fuel injector nozzle

Clean or replace nozzle.

Throttle lever out of adjustment

Adjust throttle lever.

Improper fuel flow

Check strainer, gage and flow
at the fuel line.

Restriction in air scoop

Examine air scoop and remove
restrictions.

Improper fuel

Drain and refill tank with
recommended fuel.

Faulty ignition

Tighten all connections. Check
system with tester. Check
ignition timing.

Rough Engine

Cracked engine mount

Replace or repair mounting.

Defective mounting bushings

Install new mounting bushings.

Uneven compression

Check compression.

Plugged fuel injector nozzle

Clean or replace nozzle.

Low Oil Pressure

Insufficient oil

Fill sump to proper level with
recommended oil.

Air lock or dirt in relief valve

Remove and clean oil pressure
relief valve.

Leak in suction line or pressure

Check gasket between accessory

line

housing and crankcase.

High oil temperature

See High Oil Temperature in

Trouble column.

6-3

Содержание TIO-540-A1A











































































































































Результаты поиска

Содержание TIO-540-A1A

Отзывы:

Похожие инструкции для TIO-540-A1A

Бренды по названию

Популярные бренды

Lycoming TIO-540-A1A, Руководство оператора

Результаты поиска

Содержание TIO-540-A1A

Отзывы:

Похожие инструкции для TIO-540-A1A

Бренды по названию

Популярные бренды