Lycoming TIO-540-A1A Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 138

background image

LYCOMING OPERATOR’S MANUAL

SECTION 3

TIO-540 SERIES – ANGLE VALVE CYLINDER HEADS

OPERATING INSTRUCTIONS

SECTION 3

OPERATING INSTRUCTIONS

1. GENERAL.

Close adherence to these instructions will greatly contribute to long life, economy and

satisfactory operation of the engine.

NOTE

YOUR ATTENTION IS DIRECTED TO THE WARRANTIES THAT APPEAR IN THE
FRONT OF THIS MANUAL REGARDING ENGINE SPEED, THE USE OF SPECIFIED
FUELS AND LUBRICANTS, REPAIRS AND ALTERATIONS. PERHAPS NO OTHER ITEM
OF ENGINE OPERATION AND MAINTENANCE CONTRIBUTES QUITE SO MUCH TO
SATISFACTORY PERFORMANCE AND LONG LIFE AS THE CONSTANT USE OF
CORRECT GRADES OF FUEL AND OIL, CORRECT ENGINE TIMING, AND FLYING
THE AIRCRAFT AT ALL TIMES WITHIN THE SPEED AND POWER RANGE SPECIFIED
FOR THE ENGINE. DO NOT FORGET THAT VIOLATION OF THE OPERATION AND
MAINTENANCE SPECIFICATIONS FOR YOUR ENGINE WILL NOT ONLY VOID YOUR
WARRANTY BUT WILL SHORTEN THE LIFE OF YOUR ENGINE AFTER ITS WARRANTY
PERIOD HAS PASSED.

New engines have been carefully run-in by Lycoming and therefore, no further break-in is necessary

insofar as operation is concerned. New or newly overhauled engines should be operated using only the
lubricating oil recommended in the latest revision of Service Instruction No. 1014.

NOTE

Cruising should be done at 65% to 75% power until a total of 50 hours has accumulated or
oil consumption has stabilized. This is to insure proper seating of the rings and is applicable
to new engines, and engines in service following cylinder replacement or top overhaul of one
or more cylinders

The minimum fuel octane rating is listed in the flight chart, Part 8 of this section. Under no circumstances

should fuel of a lower octane rating or automotive fuel (regardless of octane rating) be used.

2. PRESTARTING ITEMS OF MAINTENANCE.

Before starting the aircraft engine for the first flight of the

day, there are several items of maintenance inspection that should be performed. These are described in
Section 4 under Daily Pre-Flight inspection. They must be observed before the engine is started.

3. STARTING PROCEDURES.

The following starting procedures are recommended; however, the starting characteristics of various

installations will necessitate some variation from these procedures.

NOTE

Cranking periods should be limited to ten (10) to twelve (12) seconds with 5 minutes rest
between cranking periods.

3-1

«
...
23
24
25
26
27
...
»

Содержание TIO-540-A1A











































































































































Отзывы:

Нет отзывов

Похожие инструкции для TIO-540-A1A

Бренд: Yardney Страницы: 8

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: IAI Страницы: 5

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды