Lycoming TIO-540-A1A Скачать руководство пользователя страница 120

Страница: 120 / 138

SECTION 6

LYCOMING OPERATOR’S MANUAL

TROUBLE-SHOOTING

TIO-540 SERIES – ANGLE VALVE CYLINDER HEADS

TROUBLE

PROBABLE CAUSE

REMEDY

Failure of Engine to Idle Properly

Incorrect idle mixture

Adjust mixture.

Leak in induction system

Tighten all connections in the
induction system. Replace any
parts that are defective.

Incorrect idle adjustment

Adjust throttle stop to obtain
correct idle.

Uneven cylinder compression

Check condition of piston rings
and valve seats.

Faulty ignition system

Check entire ignition system.

Insufficient fuel pressure

Adjust fuel pressure.

Leak in air bleed nozzle balance

Check connection and replace if

line

necessary.

Plugged fuel injector nozzle

Clean or replace nozzle.

Flow divider fitting plugged

Clean fitting.

Low Power and Uneven

Mixture too rich; indicated by

Readjustment of fuel injector

Running

sluggish engine operation, red

or carburetors by authorized

exhaust flame at night. Extreme

personnel is indicated.

cases indicated by black smoke
from exhaust

Mixture too lean; indicated by

Check fuel lines for dirt or other

overheating or backfiring

restrictions. Readjustment of fuel
injector or carburetor by author-
ized personnel is indicated.

Leaks in induction system

Tighten all connections. Replace
defective parts.

Defective spark plugs

Clean and gap or replace spark
plugs.

Improper fuel

Fill tank with fuel of recom-
mended grade.

Magneto breaker points not

Clean points. Check internal

working properly

timing of magnetos.

6-2

Содержание TIO-540-A1A











































































































































Результаты поиска

Содержание TIO-540-A1A

Отзывы:

Похожие инструкции для TIO-540-A1A

Бренды по названию

Популярные бренды

Lycoming TIO-540-A1A, Руководство оператора

Результаты поиска

Содержание TIO-540-A1A

Отзывы:

Похожие инструкции для TIO-540-A1A

Бренды по названию

Популярные бренды