manualshive.com logo in svg

Lycoming TIO-540-A1A, Руководство оператора

Операторский мануал для двигателя Lycoming TIO-540-A1A теперь доступен для бесплатного скачивания на нашем сайте. Получите подробное руководство по эксплуатации этого двигателя, чтобы обеспечить его надежную работу. Скачайте руководство с нашего сайта прямо сейчас.

Поделиться
Скачать
background image

SECTION 5

LYCOMING OPERATOR’S MANUAL

MAINTENANCE PROCEDURES

TIO-540 SERIES – ANGLE VALVE CYLINDER HEADS

a. Removal of Cylinder Assembly –

(1) Remove exhaust manifold.

(2) Remove rocker box drain tube, intake pipe, baffle and any clips that might interfere with the

removal of the cylinder.

(3) Disconnect ignition cables and remove the bottom spark plug.

(4) Remove rocker box cover and rotate crankshaft until piston is approximately at top center of the

compression stroke. This is indicated by a positive pressure inside of cylinder tending to push
thumb off of bottom spark plug hole.

(5) Slide valve rocker shafts from cylinder head and remove the valve rockers. Valve rocker shafts

can be removed when the cylinder is removed from the engine. Remove rotator cap from exhaust
valve stem.

(6) Remove push rod by grasping ball end and pulling rod out of shroud tube. Detach shroud tube

spring and lock plate and remove shroud tubes from cylinder head.

NOTE

The hydraulic tappets, push rods, rocker arms and valves must be assembled in the same
location from which they were removed.

(7) Remove cylinder base nuts and hold down plates (where employed) than remove cylinder by

pulling directly away from crankcase. Be careful not to allow the piston to drop against the
crankcase, as the piston leaves the cylinder.

b. Removal of Piston from Connecting Rod –

Remove the piston pin plugs. Insert piston pin puller

through piston pin, assemble propeller nut; then proceed to remove piston pin. Do not allow
connecting rod to rest on the cylinder bore of the crankcase. Support the connecting rod with heavy
rubber band, discarded cylinder base oil ring seal, or any other non-marring method.

c. Removal of Hydraulic Tappet Sockets and Plunger Assemblies –

It will be necessary to remove and

bleed the hydraulic tappet plunger assembly so that dry tappet clearance can be checked when the
cylinder assembly is reinstalled. This is accomplished in the following manner:

(1) Remove the hydraulic tappet push rod socket by inserting the forefinger into the concave end of

the socket and withdrawing. If the socket cannot be removed in this manner, it may be removed
by grasping the edge of the socket with a pair of needle nose pliers. However, care must be
exercised to avoid scratching the socket.

(2) To remove the hydraulic tappet plunger assembly, use the special Lycoming service tool. In the

event that the tool is not available, the hydraulic tappet plunger assembly may be removed by a
hook in the end of a short piece of lockwire, inserting the wire so that the hook engages the spring
of the plunger assembly. Draw the plunger assembly out of the tappet body by gently pulling the
wire.

CAUTION

NEVER USE A MAGNET TO REMOVE HYDRUALIC PLUNGER ASSEMBLIES FROM
THE CRANKCASE. THIS CAN CAUSE THE CHECK BALL TO REMAIN OFF ITS SEAT,
RENDERING THE UNIT INOPERATIVE.

5-8

Содержание TIO-540-A1A











































































































































Отзывы:

Нет отзывов

Похожие инструкции для TIO-540-A1A

Caen V793 Technical Information Manual preview
V793
Бренд: Caen Страницы: 20
Fanimation BTCR9 Quick Start Manual preview
BTCR9
Бренд: Fanimation Страницы: 2
M2M C600 Technical Manual preview
C600
Бренд: M2M Страницы: 24
GCE S 400 Operating Instructions Manual preview
S 400
Бренд: GCE Страницы: 24
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Бренд: YOKOGAWA Страницы: 150
YOODA NANO Series Quick Start Manual preview
NANO Series
Бренд: YOODA Страницы: 3
YMGI 584 Series User Manual preview
584 Series
Бренд: YMGI Страницы: 8
Cypress CY3280-BK1 Quick Start Manual preview
CY3280-BK1
Бренд: Cypress Страницы: 3
INSBUD IB-TRON 4000 SOL Instruction Manual preview
IB-TRON 4000 SOL
Бренд: INSBUD Страницы: 14
Rain Bird IQ-NCC Installation And User Manual preview
IQ-NCC
Бренд: Rain Bird Страницы: 48
Sullair 02250160-842 Instruction Manual preview
02250160-842
Бренд: Sullair Страницы: 31
SILENTRON SERENYA 2000 Manual preview
SERENYA 2000
Бренд: SILENTRON Страницы: 20
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Бренд: MacroAir Technologies Страницы: 32
IFM EC2121 System Manual preview
EC2121
Бренд: IFM Страницы: 41
Duco iAV Quick Start Manual preview
iAV
Бренд: Duco Страницы: 16
Samson 46-7 Mounting And Operating Instructions preview
46-7
Бренд: Samson Страницы: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Бренд: Hansen Страницы: 12
Ocean Breeze RG15A/E Manual preview
RG15A/E
Бренд: Ocean Breeze Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды