background image

 

Colibri II

 – Flight recorder and navigation instrument 

Page 6 

Main page 

The  main  page  consists  of  basic  flight  parameters.  In  the  left  upper  corner 
ground speed information is shown. To the right of the ground speed display, 
the GPS signal status is shown (green bars), where 1 bar represent 3 satellites 
and 5 bars for more than 6 satellites. The battery indicator is shown in the top 
right  corner.  When  the  internal  charger  is  charging  the  battery,  the  battery 
indicator  is  replaced with the  charging  “plug”  symbol.  The  central  part  of  the 
main  page  is  the  vario  indicator  with  yellow  needle  and  numeric  average 
indicator  in  middle.  The  vario  needle  deflection  is  ±4m/s  (±8knots)  but  the 
numerical average is not limited.  

A  wind  indicator  in  the  central  left  part  of  the  display  shows  the  wind  direction  and  speed.  An  arrow 
shows  the  wind  direction  with  respect  to  your  track.  The  first  wind  indication  will  appear  after  2  full 
turns. The lower part of the page shows a QNH altitude and the vario volume.   

Note! 

Altitude reading doesn’t correspond to IGC recorded altitude, if QNH setting is different than 1013. 

 
Buttons: 
Left -> setup page 
Right -> TP navigation page 
Up, down -> vario volume change 
In = Enter -> thermal assistant 
 

Thermal assistant 

Pressing  the  enter  button in  the  main page will activate  the  thermal assistant. 
An  automatic  switch  from  the  main  page  is  also  possible  by  selecting  the 
Thermal  assistant  item  in  the  setup/vario  menu.  The  Thermal  assistant  page 
shows the thermal profile in colors as percent of the maximum climb rate in the 
last  circle.  The  red  dots  represent  70%  or  more,  yellow  50-70%  and  blue  less 
than  50%  of  the  maximum.  No  dot  means  negative  vario  and  the  white  dot 
shows  the  maximum.    The  top  right  corner  of  the  screen  shows  the  overall 
thermal  average  which is  the  average climb rate  from the  start of  the thermal 
until the end of the thermal (total average).  In the bottom right corner altitude 
gain for the thermal is shown. The numeric figures inside the circle show the current vario and the arrow 
shows wind direction. 

Buttons: 
Left -> setup page 
Right -> TP navigation page / Flarm radar page 
Up, down -> no effect 
Enter -> main page 

Содержание Colibri II



























Отзывы: