Luxul XMS-1008P Скачать руководство пользователя страница 35

Страница: 35 / 40

User Guide

MAC Aging Confi guration:



ARL Aging:

Check to enable this function or uncheck to disable. It is enabled by

default

NOTE:

It is not recommended to disable ARL Aging



Aging Time:

Sets the aging time. 300 seconds by default.

NOTE:

It is not recommended to have an Aging Time setting greater
than 3600 seconds.

CAUTION:

If “ARL Aging” is unchecked, the switch stops learning new

MAC addresses and the addresses in the MAC address table
turn into static MAC entries and are free from aging. This is
not recommended.

5.13.7 Restore Factory Defaults

Restore Factory Defaults:

Click “Apply” to restore the factory default

confi guration

CAUTION:

Restoring default confi guration will re-set all of your

settings to factory defaults. The switch will now have the
default IP address 192.168.0.3. For login, both default user
name and default password are “admin.”

5.13.8 Backup

Backup Current Settings:

Click “Backup” to backup the current switch confi gura-

tion settings to a fi le

Содержание XMS-1008P









































Результаты поиска

Содержание XMS-1008P

Отзывы:

Бренды по названию

Популярные бренды

Luxul XMS-1008P, Руководство пользователя

Результаты поиска

Содержание XMS-1008P

Отзывы:

Бренды по названию

Популярные бренды