manualshive.com logo in svg

Luxul XMS-1008P, Руководство пользователя

Поделиться
Скачать
Luxul XMS-1008P Скачать руководство пользователя страница 16

User Guide

16

© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

 

NOTE:

  If the selected rate is higher than the actual connection rate of 

the client device, the device will operate at its maximum data 
rate.

Rate Limit:

 Displays the bandwidth control status of all ports, as shown below.

5.3.3 Storm Control 

Storm Control:

 Suppresses the transfer of bandwidth limiting broadcast packets 

through the switch. When broadcast packets reach the set bandwidth limitation, 
the XMS-1008P automatically discards the packet to ensure a stable environment 
that is free from broadcast storms. 

 

Broadcast Rate: 

The allowed bandwidth rate of broadcast packets. Default is 

108kb or 1mb/second.

 

Multicast Rate:

 The allowed bandwidth rate of multicast packets. Default is 

108kb or 1mb/second. 

 

NOTE:

 If multicast streaming is used in your environment you will want 

to raise this limit from the default..

 

Unknown Unicast Rate (Flood): 

The allowed bandwidth rate of fl ood packets.  

Default is 108kb or 1mb/second. 

 

CAUTION:

  This value should not be raised without the assistance of a 

Network Administrator in determining if it is necessary.

 

NOTE:

  The XMS-1008P does not completely suppress broadcast 

packets. Instead it only limits the transmission rate for broadcast 
packets.

Содержание XMS-1008P









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды