manualshive.com logo in svg

Luxul XMS-1008P, Руководство пользователя

Поделиться
Скачать
Luxul XMS-1008P Скачать руководство пользователя страница 32

User Guide

32

© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

5.13 System 

 

5.13.1 SNMP

 

5.13.2 Change Password 

 

5.13.3 Power Save

 

5.13.4 Upgrade

 

5.13.5 IP Confi guration

 

5.13.6 MAC Aging 

 

5.13.7  Restore Factory 

Defaults

 

5.13.9 Restore 

 

5.13.10 Logout

5.13.1 SNMP

All management information and counters are stored in the Management 

Information Base (MIB) of the switch. The XMS-1008P adopts standard MIB-II 

modules that support read function from any SNMP-based NMS software. MIB data 

may be set to either read-only or read-write mode. 

 

The default SNMP community names of the switch can be user modifi ed. 

 

Traps are messages generated by the XMS-1008P and used for notifi cation of 
certain events. Such events may be serious (i.e. switch reboot) or ordinary (i.e. 
the status changes of a switch port). The XMS-1008P can generate traps and send 
them to the NMS. 

SNMP Confi guration

 

SNMP:

 Enables or disables the SNMP management function. SNMP is enabled by 

default 

 

SNMP Trap Destination: 

Sets the destination IP address of the Trap messages 

generated by the XMS-1008P 

 

SNMP Read Community:

 Sets the read-only community name. For a device to 

read the SNMP information of the XMS-1008P, the SNMP management software 
must contain the read-only community name

 

SNMP Write Community:

 Sets the read/write community name. For a device 

to modify the SNMP information on the XMS-1008P, the SNMP management 
software must contain the read/write community name

 

SNMP Trap Community: 

Used by the SNMP management software to identify 

the switch sending the Trap message

Содержание XMS-1008P









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды