LuxCom OM1004 Скачать руководство пользователя страница 4

Description

Description

The OM1004 Ethernet switch has three 1000BASE-X optical ports and one 10/100/1000BASE-T 

electrical port.  Rapid Spanning Tree (RSTP) allows redundant connections between nodes.  A 

dip switch allows plug and play RSTP, while the serial console port allows for an RSTP 

configuration tailored to specific needs.  Optics for multimode, singlemode, and single fiber 

applications are available.  A universal AC power supply is built in, while an auxiliary 5V DC input 

from an external power cube (not supplied) allows for power source redundancy.  The OM1004 

is enclosed in a rugged metal case for low radiated and conducted emissions.  It does not 

support jumbo packets.

Features

RSTP algorithm allows redundant links
One 10/100/1000BASE-T electrical port
Three 1000BASE-X optical ports
Plug and play operation 
Redundant power supply inputs

Single or multimode fiber option
Single bidirectional fiber option
SC or ST optical connectors 
Temperature range -10°C to 70°C
Distances up to 100 km
5 Year warranty

Indicators

LNK

Link

On

 when a bidirectional optical or electrical LINK has been 

established with a remote Ethernet port.

Flashing

 when data is being transmitted or received.

STP

Spanning Tree 

Green

 when the port is forwarding packets in RSTP mode.

Yellow

 when the port is blocking packets (is a standby link).  

Note that only one end of a blocked link shows the blocking state; 
however the remote link indicator will not flash which indicates it is 
not passing data, and is therefore a backup link.

Green/Yellow

 when the port is in the  transitory learning state.

Off

 when the port is not in RSTP mode.

SPD

Speed

Green

 when electrical port is 1000BASE-T.

ALARM

The switches on the back of the OM1004 control this indicator.  It is 

on

 when the link for a 

required

 port is off, or no link is present on 

any port.  When a port is 

required

 for proper network operation, the 

corresponding switch should be up.  The front panel Alarm indicator 
will then come on (

red

) when a required link fails.  This gives a 

visual indication of link failure.  This is especially important in a 
redundant fiber configuration where the failure would not cause a 
data transfer failure, and would hence go unnoticed.  If the 
electrical port is connected to a computer which is turned off at the 
end of the day, switch five which controls that port should be down 
(off) to avoid unnecessary alarms. 

1   

Содержание OM1004














Отзывы: