LuxCom OM1004 Скачать руководство пользователя страница 11

Software Menu

:> 3
BACKUP file is now PRIMARY file
:> 2
Delete BACKUP file (y/n): y
Start Xmodem transfer (Send File)
CCCCCC
File upload successful
233984 bytes uploaded
:> 3
BACKUP file is now PRIMARY file
:> 4
Luxcom Technologies Inc.
OM1004 Ethernet Bridge BootLoader (Rev 1.0)
Erasing flash...
Writing flash...............................
Starting application...

Luxcom Technologies Inc.
OM1004 Ethernet Bridge Application (Rev. 1.1)

FreeRTOS.org V5.2.0 - Copyright (C) 2003-2009 Richard Barry.
lwip - Copyright (c) 2001-2003 Swedish Institute of Computer Science.
rstp - Copyright (c) 2007 EMC Corporation.

OM1004 Main Menu
1    Ethernet menu
2    Bridge RSTP menu
3    Software menu
:>

After  the OM1004 requests the user to start the Xmodem transfer, the user must select the Xmodem 
protocol and the upload file (e.g., using HyperTerminal's Transfer/Send File menu option).  The 
OM1004 send C's for thirty seconds.  This is an indication to the terminal program to use the Xmodem 
CRC protocol.  After thirty seconds, the OM1004 switches to sending NAK characters every ten 
seconds for another 100 seconds.  This is an indication to the terminal program to use Xmodem 
checksum mode.  Thus, a user has approximately 130 seconds to select the upload file.  Usually, it 
doesn't matter whether the transfer occurs in CRC or checksum mode, however, some terminal 
programs don't switch automatically from CRC to checksum mode.  In that case, it may be necessary 
to select the upload file in the first thirty seconds, or defer selecting the upload file until the OM1004 
has switched to checksum mode.

  

8   

Содержание OM1004














Отзывы: