Lux Tools 451 121, Инструкция по эксплуатации

Страница: 5 / 16

5
• Prevent unintentional starting. Ensure the
switch is in the off-position before connect-
ing to power source and/or battery pack,
picking up or carrying the tool.
Carrying
power tools with your finger on the switch or
energizing power tools that have the switch on
invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better con-
trol of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of these devices can reduce dust-
related hazards.
Power tool use and care
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool.
Power tools are dangerous
in the hands of untrained users.
• Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool’s operation. If damaged, have
the power tool repaired before use.
Many
accidents are caused by poorly maintained
power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
• Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts.
This will ensure that the safety of
the power tool is maintained.
Safety notes for hammering
• Wear ear defenders when hammer drilling.
The effects of noise may lad to loss of hearing.
• Use the additional handles supplied with the
unit. Loss of control may lead to injuries.
• Hold the device by the insulated surfaces
when carrying out work during which it is
possible that the tool or screw may come
across hidden power cables or its own cable.
Contact with a power-carrying cable may also
put metal parts of the unit under power and
cause an electric shock.
Additional safety notes
• Prior to starting work, use appropriate tool to
determine whether there are any hidden sup-
ply lines are located on the area you are work-
ing in. If in doubt, ask the relevant supply ser-
vices.
Contact with power lines may cause fire
and electrical shock. Damaging a gas pipe may
cause an explosion. Damaging a water pipe
leads to considerable property damage and may
cause electrical shock.
• Avoid uncontrolled restarting. Switch the tool
off when the power supply is interrupted, for
example, by a power failure or pulling the plug.
• Wait until the power tool has come to a stand-
still before you put it down. The inserted tool
may otherwise jam and cause a loss of control
over the power tool.
• Secure the work piece. Use tensioning equip-
ment or a vice to secure the work piece to help
prevent kickback or uncontrolled flying of the
work piece (e.g. when getting jammed in the
work piece).
• Immediately switch off the power tool when
the inserted tool becomes blocked. Be pre-
pared for high responses instances in the
event of kickback.
The inserted tool will jam
when the power tool is overloaded or tilted
within the work piece.
• Never use the power tool with a damaged
cable. Do not touch a damaged cable and pull
out the power plug immediately.
Damaged
cables increase the risk of electric shock.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to jam and are easier to con-
trol.
• Prevent overheating of the device and the
work piece. Excess heat may damage the tool
and the device.
• Shortly after being used, the tool may be very
hot. Allow a hot tool to cool down. Touching
a hot tool may cause burns.
• Never clean a hot tool with flammable liq-
uids. There is a risk of fire and explosion.
• Keep the handles dry and free of grease.
Slippery handles can lead to accidents.
• When working, hold the power tool firmly with
both hands and ensure you have a stable
footing.
The power tool can be guided in a safer
fashion when you use two hands.
GB
Bohrhammer_451121.book Seite 5 Donnerstag, 17. September 2015 8:08 08