Lutz-Jesco MEMDOS LB Скачать руководство пользователя

Страница: 36 / 44

Troubleshooting

Type of fault

BA-10407-02-V08

Motor-driven diaphragm dosing pump

MEMDOS LB

Operating instructions

13.1.3 Delivery rate varies

Possible cause

Remedy

Valve leaking or blocked

Clean the valve and vent the
dosing pump.

Tighten the screw connections.

Valve damaged (e.g. valve
balls)

Remove the damaged parts or
install a new valve.

Suction line is leaking

Seal the leak locations or replace
the parts.

Suction line is blocked (e.g.
screen in foot valve)

Clean the suction line.

Viscosity too high

Possibly reduce the concentration
of the dosing medium or increase
the temperature.

Install spring-loaded valves.

Increase the pipe diameter.

The drive motor's electrical
data does not match that of
the mains supply

Check the electrical installation.

Suction side pressure too high
(pump siphoning)

Install a back-pressure valve in
the pressure line.

Pressure peaks due to
acceleration with long suction
lines

Install a suction pressure
regulator.

Imprecise dosing due to
changeable positive and
negative suction heads.

Install a suction pressure
regulator.

System backpressure too
high (measured at discharge
connection of dosing pump)

Clean blocked injection nozzle.

Install pulsation dampeners to
reduce pressure peaks if pipes
are too long.

Check the safety valves.

Table 32: Type of fault: Delivery rate varies

13.1.4 No stroke movement observed

Possible cause

Remedy

Dosing pump set to zero
stroke.

Set the stroke length adjusting
knob correctly.

Diaphragm return spring
broken.

Contact the manufacturer.

Current supply interrupted

Reconnect the current supply

The drive motor's electrical
data does not match that of
the mains supply

Check the electrical installation.

Table 33: Type of fault: No stroke movement observed

13.1.5 Dosing pump delivery rate too high

Possible cause

Remedy

Suction side pressure too high
(pump siphoning)

Install a back-pressure valve in
the pressure line.

Pressure peaks due to
acceleration with long suction
lines

Install a suction pressure
regulator.

Table 34: Type of fault: Dosing pump delivery rate too high

13.1.6 Diaphragm is torn or tears too often

Possible cause

Remedy

Shut-off valves closed

Open the shut-off valves. Inspect
the dosing pump for possible
damage.

Pressure peaks due to
acceleration with long suction
lines

Install a suction pressure
regulator.

The materials are not suitable
for the dosing medium being
used

Check the resistance of the
materials.

Diaphragm not screwed up to
the end stop on the dia-
phragm rod

Screw a new diaphragm up to the
end stop.

System backpressure too
high (measured at discharge
connection of dosing pump)

Clean blocked injection nozzle.

Install pulsation dampeners to
reduce pressure peaks if pipes
are too long.

Check function of safety valves.

Media sediment in dosing
head

Clean the dosing head.

Table 35: Type of fault: Diaphragm is torn or tears too often

13.1.7 Loud noises on the dosing pump

Possible cause

Remedy

Drive components worn

Contact the manufacturer.

Table 36: Type of fault: Loud noises on the dosing pump

Содержание MEMDOS LB













































Результаты поиска

Содержание MEMDOS LB

Отзывы:

Похожие инструкции для MEMDOS LB

Бренды по названию

Популярные бренды

Lutz-Jesco MEMDOS LB, Руководство по эксплуатации

Результаты поиска

Содержание MEMDOS LB

Отзывы:

Похожие инструкции для MEMDOS LB

Бренды по названию

Популярные бренды