Luminex LumiNode 1 Скачать руководство пользователя страница 8

Страница: 8 / 40

Alternatively, the LumiNode series are 802.3af compliant (PoE), so that each LumiNode will act as a

PD (Powered Device) and can be powered by any compliant PSE (Power Sourcing Equipment) such as

Ethernet switch, midspan and PoE injector. All models can only be powered with PoE via ETH2!

2.3 Connection to the network

To get the LumiNode 4

DIN

online in your system, connect either port ETH1 or ETH2 to a computer, or to a

port of an Ethernet switch.

Only port ETH2 on the rear of the unit can be used to power the unit through PoE. Check the port labelling

for a better identification.

2.4 leD indicators

There are various LEDs on the LumiNode 4

DIN

. Here is a list of the LEDs, the possible colours, and the

meaning of each colour:

DMX PORT

STATUS

MEANING

DMX Input

Green

Input idle

Green flashing

Input active

DMX only (output mode)

Cyan

Output idle

Cyan flashing

DMX activity

DMX + RDM (output mode)

Blue

Output idle

Blue flashing

DMX activity

Stream loss

Red

Source stream lost

Red flashing

Source stream lost but still outputting the last received packets

Orange flashing

Source stream recovered

DMX redundancy

Magenta

Output idle

Magenta flashing

Output active

NETWORK PORT

Bottom LED (Link)

Green

Gigabit connection (flashing: Ethernet traffic)

Orange

100Mbit connection (flashing: Ethernet traffic)

Top LED (Mode)

Blue

Default colour

Green flashing

Device booting

Orange flashing

Firmware upgrade in progress

Green blinking

Identify in progress

Group colour

Corresponding to assigned group/VLAN

POWER

Power/OK LED

Red

Device booting

Green

Device booted and online

2 | InstallatIon

Содержание LumiNode 1









































Результаты поиска

Содержание LumiNode 1

Отзывы:

Похожие инструкции для LumiNode 1

Бренды по названию

Популярные бренды

Luminex LumiNode 1, Руководство пользователя

Результаты поиска

Содержание LumiNode 1

Отзывы:

Похожие инструкции для LumiNode 1

Бренды по названию

Популярные бренды