manualshive.com logo in svg

Luminex LumiNode 1, Руководство пользователя

Поделиться
Скачать
Luminex LumiNode 1 Скачать руководство пользователя страница 7

n

m

2.1  mounting the device

LumiNode 4

DIN

 is designed to be mounted directly onto a standard DIN (IEC/EN 60715) rail. Before fitting the 

device, please make a note of the IP address as this is located at the bottom of the device.

The device clips onto the rail.

Insert the LumiNode 4 DIN  from the top to the bottom until you hear the bottom clip connection. It is 

recommended to relief strain from the bottom clip by gently using a sharp tool as a leaver.

To remove the unit from the rail, use a sharp tool and insert it in the hole of the bottom clip. Slightly push 

the clip to the bottom to release the LumiNode 4

DIN

 from the rail.

Since the unit requires no user intervention once installed, they are suitable for remote installation with all 

configuration and management taking place over an Ethernet network.

However, it is recommended that access can be gained in the unlikely event of a hardware failure.

2.2  Power up the device

The LumiNode 4

DIN 

can be powered with a 12-24V DC power supply 

(M)

. The device will automatically 

switch on. To shut it down after use, just un-plug the power cable again. The LumiNode 4

DIN

 can also be 

powered with Power over Ethernet (PoE) 

(N)

.

7

2. Installation

2. Installation

Содержание LumiNode 1









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды