Lumel N32O Скачать руководство пользователя страница 2

Страница: 2 / 69

N32O

User's manual

Contents

4.1 Installation method...................................................................................................................6
4.2 External connection diagram....................................................................................................7

5 Service............................................................................................................................................10

5.1 Description of the frontal plate...............................................................................................10
5.2 Buttons' functions...................................................................................................................12
5.3 Programming meter parameters..............................................................................................13

5.3.1 How to change quantity of a selected parameter............................................................16
5.3.2 Programmable meter parameters, default parameters.....................................................16

5.4 Meter functions.......................................................................................................................23

5.4.1 Measurement...................................................................................................................23

5.4.2 Analog output..................................................................................................................42
5.4.3 Alarm outputs..................................................................................................................43

5.5 RS-485 interface.....................................................................................................................45

5.5.1 Connection......................................................................................................................45
5.5.2 Description of the MODBUS protocol implementation.................................................46
5.5.3 Implemented functions of MODBUS protocol...............................................................46
5.5.4 Map of the registers.........................................................................................................47

5.5.4.1 Registers 4000 – 4079.............................................................................................47
5.5.4.2 Registers 4200 – 4257.............................................................................................54
5.5.4.3 Registers 7500 – 7521 and 7000 – 7043.................................................................56
5.5.4.4 Registers 7600 – 7744 and 7200 – 7489.................................................................57

6 Error codes......................................................................................................................................62
7 Technical data.................................................................................................................................63
8 Ordering code.................................................................................................................................67

Содержание N32O






































































Результаты поиска

Содержание N32O

Отзывы:

Lumel N32O, Руководство пользователя, Страница: 2 / 69

Результаты поиска

Содержание N32O

Отзывы: