Lumel N32O Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 69

Lumel N32O Скачать руководство пользователя страница 62

N32O

User's manual

62

6 Error codes

The N32O meters have several diagnostic functions and settings built-in that allow to limit
the displaying. So the display may show and the status registers may store information
about the diagnosed error, event or fault. Possible messages and their potential causes
are listed below.

Message

Description

Overflow of the lower value of the measuring range value or the programmed
indication range.

Overflow of the upper value of the measuring range value or the programmed
indication range.

It is not possible to display the measuring value in the selected resolution - the
measurement result does not fit on the display. Lower the display resolution or
select the mode of automatic position of the decimal point.

Lost calibration. Please contact the technical support.

Lost real time clock settings. The message is displayed only when turning the
meter on. Time and date must be set. If the message still appears when turning
the   meter   on   after   setting   the   time   and   date,   please   contact   the   Service
Department   because   a   backup   battery   may   require   to   be   replaced.   This
message   can   be   ignored   if   the   clock   settings   are   not   significant   in   a   given
application.

Measurement module error. It is not possible to make a measurement, please
contact the technical support.

Configuration data memory and calibration memory error. It is not possible to
use a meter, please contact the technical support.

No communication with the analog output module. Please contact the Service
Department.

«
...
60
61
62
63
64
...
»

Содержание N32O






































































Отзывы:

Нет отзывов