Lufft 8371.UA01 Скачать руководство пользователя страница 19

Страница: 19 / 76

Operating Manual V25/09.2019

Ventus / Ventus-X / V200A

Chapter 10 Connections

(for SDI12 connection please always follow the detailed notes in Chap. 10.7)

The connection cable screen must NOT be laid to ground in the control panel for

Ventus

The

Ventus

will be earthed through the screws with the earthed mast .

The connection cable screen MUST be laid to ground in the control panel for V200A !

If the equipment is not connected correctly

It may not function

It may be permanently damaged

The possibility of an electrical shock may exist under certain circumstances

10.1 Supply Voltage

The supply voltage for

Ventus

is 24V DC ± 10%. The power supply unit used must be approved

for operation with equipment of protection class III (SELV).

10.2 RS485 Interface

The equipment has an electrically isolated RS485 interface for configuration, measurement
polling and the firmware update.

The RS485 interface is designed as optionally half or full duplex, 2 or 4 wire connection.

The following operating restrictions exist depending on the half or full duplex operation setting:

Full duplex

Half duplex

Autonomous telegram transmission is
possible

No autonomous telegram transmission
possible

Transmission of values via current output is
not possible

Transmission of values via current output is
possible

Heating control via control pin is possible

Triggering of NMEA telegram transmission
over Control-PIN is possible

Triggering of NMEA telegram transmission
over Control-PIN is not possible

SDI-12 Mode not possible

SDI-12 Mode possible

Firmware update not possible

Firmware update possible

Restrictions in full and half duplex operation

See page 32 for technical details.

10.3 Analog Interface Circuits

2 analog interface circuits are provided for analog data transmission. Both are updated every
250ms.

Interface A can be configured for 0 or 4-20mA current output, 0 or 2-10V voltage output as well
as for frequency output in the range from 2

– 2000Hz (with adjustable voltage level up to 10V)

Note

: For the use of the analog outputs the serial communication protocol must be set to UMB

binary!

Interface B can be configured for 0 or 4-20mA current output and 0 or 2-10V voltage output

The channels to be transmitted by way of these interfaces can be adjusted with the aid of the
UMB-Config-Tool. The default values are Channels 400 (current wind speed in m/s (A)) and 500
(current wind direction (B)).

The scaling of the outputs is also adjustable.

The maximum load on the current output is 300



Factory setting

Содержание 8371.UA01













































































Результаты поиска

Содержание 8371.UA01

Отзывы:

Похожие инструкции для 8371.UA01

Бренды по названию

Популярные бренды

Lufft 8371.UA01, Руководство пользователя

Результаты поиска

Содержание 8371.UA01

Отзывы:

Похожие инструкции для 8371.UA01

Бренды по названию

Популярные бренды