LUDLUM 3030 Скачать руководство пользователя страница 17

Страница: 17 / 79

Model 3030 & 3030E Series

Technical Manual

Section 2

Ludlum Measurements, Inc.

Page 5

November 2017

Connect the instrument to mains power using the power cable provided and
then turn the instrument on “|” using the front panel power switch (lower

left corner).

Upon power-up, the LCD displays become backlit, front panel indicators

(LEDs) illuminate, and the alpha display shows all eights (888888). Then the
firmware version is displayed. Parameters will display before initialization

completes if the “Show Parameters during power-up” box is checked in
“General Settings” within the interface program. After initialization is

complete, both displays are blanked, and all front-panel indicators (LEDs)
are turned off.

If using the computer interface, start the interface program from the
appropriate directory and set the desired operating parameters described in

detail in Section 6 of this manual

Perform a QC check by following the directions imprinted on the

instrument front panel if available, ensuring the tray latch switch (Model
3030) is placed in the

TRAY UNLATCHED

position before attempting to pull

out the tray. Once the tray is slid out, place the check source in the center,
slide the tray back in place, and place the tray latch switch in the

TRAY

LATCHED

position. See Section 6 of this manual for further details on “QC

Check.”

The

COUNT TIME MINUTES

switch should be set based on the count rates

being observed and the desired statistical accuracy. Set the

VOLUME

control

to the desired level of audio.

Proceed to use the instrument. For further information on instrument

controls or functions, consult Sections 4 and 7 of this manual.

Содержание 3030
















































































Результаты поиска

Содержание 3030

Отзывы:

Похожие инструкции для 3030

Бренды по названию

Популярные бренды

LUDLUM 3030, Руководство пользователя

Результаты поиска

Содержание 3030

Отзывы:

Похожие инструкции для 3030

Бренды по названию

Популярные бренды