LTT i.LASER Series Скачать руководство пользователя

Страница: 5 / 93

Chapter 1 Safety

1.1 Safety Regulation

The i.LASER series uses a CO

Laser as a light source. It is classified as a class-IIIR

product by

CDRH (the Center for Devices and Radiological Health)

Wavelength : 10.6µm

Maximum output power : 30 ~ 100W

Visibility : Invisible

When operating the i.LASER series, be sure to always comply

with the safety regulations as following:

Do not attempt to modify or disassemble any component of the machine without

LTT technical support.

Do not open the doors of chassis and access the laser tube or electronic

components, especially while the machine power is on.

Connect the machine to a grounded outlet. Verify that the voltage of the outlet

is correct for the machine.

Do not disable the interlocks which are on top and front doors.

Be careful about the path of the invisible laser beam shown in figure. Otherwise,

eye or skin injury may result.

Содержание i.LASER Series






























































































Результаты поиска

Содержание i.LASER Series

Отзывы:

Похожие инструкции для i.LASER Series

Бренды по названию

Популярные бренды

LTT i.LASER Series, Руководство пользователя

Результаты поиска

Содержание i.LASER Series

Отзывы:

Похожие инструкции для i.LASER Series

Бренды по названию

Популярные бренды