LOYTEC L-IP Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 173

LOYTEC L-IP Скачать руководство пользователя страница 63

L-IP User Manual

63

LOYTEC

Version 6.1

LOYTEC electronics GmbH

Figure 53: Port Configuration Page.

When  selecting  a  protocol  on  a  communication  port,  the  protocol’s  communication
parameters  are  displayed  in  a  box  on  the  right-hand  side.  To  save  the  settings  of  the
currently  opened  protocol, click the

Save Settings

button. Pressing

Get Settings

retrieves

the current settings from the device.

6.2.4 IP Configuration

The TCP/IP configuration is done under the Ethernet port tab as shown in  Figure  54. The
mandatory  IP  settings,  which  are  needed  to  operate  the  device,  are  marked  with  a  red
asterisk  (IP  address,  netmask,  gateway).  The

Enable DHCP

checkbox switches between

manual entry of the IP address, netmask, and gateway address, and automatic configuration
from a DHCP server.

Figure 54: IP Configuration Page.

The device comes configured with a unique MAC address. This address can be changed in
order to clone the MAC address of another device. Please contact your system administrator
to avoid MAC address conflicts.

«
...
61
62
63
64
65
...
»

Содержание L-IP














































































































































































Отзывы:

Нет отзывов