LOYTEC L-IP Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 173

LOYTEC L-IP Скачать руководство пользователя страница 37

L-IP User Manual

37

LOYTEC

Version 6.1

LOYTEC electronics GmbH

LOYTEC electronics GmbH
www.loytec.com

Testing Board ID (1) Passed
Testing RAM Passed
Testing boot loader Passed
Testing fallback image Passed
Testing primary image Passed
Testing Flash Passed

Loading primary image Passed

Bootloader version 2
L-Switch/L-IP Primary Image loading...
Firmware version 6.0.0

Type bootshell to enter the boot shell...

Mounting file system (upgrading permissions) Passed
Starting TCP/IP networking Passed
Starting CEA-852 config. server 1 Disabled
Starting CEA-852 device Passed
Detecting CEA-709 port 1 (FT) Passed
Detecting CEA-709 port 2 (FT) Passed
Detecting CEA-709 port 3 (FT) Passed
Detecting CEA-709 port 4 (FT) Passed
Starting CEA-709 networking Passed
Starting remote LPA Passed
Starting FTP server Passed
Starting Telnet server Passed
Starting Web server Passed

L-IP(c)
LOYTEC electronics GmbH
Tue Sep 25 08:54:38 2012 - V6.0.0

Figure 25: Console messages during the boot phase.

The duration of a successful boot sequence of an L-IP is typically 12 seconds.

5.3 L-IP Configuration Menu (Main Menu)

After booting completed the L-IP displays the following console menu:

Device Main Menu
================

[1] Show device information
[2] Serial firmware upgrade
[3] System configuration
[4] CEA-709 configuration
[5] IP configuration
[6] CEA-852 device configuration
[8] Reset configuration (factory defaults)
[9] Device statistics
[s] CEA-852 server configuration

[0] Reset device

Please choose:

Figure 26: Device main menu.

The menu items are described below:

1 - Show device information

This menu item shows information about the L-IP and the current firmware version. The
output should look like what is shown in Figure 27.

«
...
35
36
37
38
39
...
»

Содержание L-IP














































































































































































Отзывы:

Нет отзывов