manualshive.com logo in svg

LOYTEC L-IP, Руководства пользователя, Страница: 56 / 173

Поделиться
Скачать
LOYTEC L-IP Скачать руководство пользователя страница 56

L-IP User Manual 

56 

LOYTEC 

Version 6.1 

LOYTEC electronics GmbH 

 

WARNING: Conflicting IP address detected! 
         IP address 10.125.123.95 also used by device with MAC address  
         00 04 5A CC 10 41! 
 
Clear IP conflict history (y/n): 

Figure 46: IP Address conflict. 

As useful information the MAC address of the conflicting host is shown. If the information 
about this conflict shall be cleared, hit ‘

y

’. If ‘

n

’ is selected, the conflict will show up again 

the next time this menu is entered. 

6 - Enhanced Communications Test 

This  menu  item  allows  testing  the  communication  path  between  L-IP  devices.  It  tests  the 
CEA-852  data  communication.  This  test  can  be  used  to  determine  if  there  is  a  working 
TCP/IP  connection  as  well  as  a  working  CEA-852  connection  between  the  individual 
devices. 

A typical console output is shown in Figure 47. 

Enhanced Communications Test 
============================ 
 
Address                    Result  RTT(ms)  Comment 
------------------------------------------------------------------------ 
10.101.18.100:1629 (CS)    OK      2         
10.101.18.100:1628         OK      2         
10.101.18.101:1628         OK      2         
10.101.18.139:1628         OK      2         
10.101.18.203:1628         OK      2         
10.101.18.156:1628         OK      2         
10.101.18.157:1628         OK      4         
10.101.18.213:1628         FAILED  n/a      Peer not reachable 
10.101.18.210:1628         OK      2         
10.101.18.20:1628          OK      106       
10.101.18.216:1628         OK      1         
10.101.18.10:1628          OK      2         
10.101.18.17:1628          OK      2         
10.101.18.12:1628          OK      1         
10.101.18.13:1628          OK      90        
10.101.18.161:1628         OK      1         
10.101.18.113:1628         OK      2         
10.101.18.114:1628         OK      2         
10.101.18.19:1628          OK      70        
192.168.1.246:1628         OK      2         
10.101.18.14:1628          OK      1         
192.168.17.2:1628          FAILED  n/a      Peer not reachable 
192.168.17.151:1628        FAILED  n/a      Peer not reachable 

Figure 47: Enhanced communication test console output. 

The round-trip value (RTT) is measured as the time a packet sent to the peer device needs 
to  be  routed  back  to  the  L-IP.  It  is  a  measure  for  general  network  delay.  If  the  test  to  a 
specific member fails a text is displayed to describe the possible source of the problem. The 
reasons for failure are summarized in Table 5. 

A  warning  “Incorrect  NAT  configuration  detected!”  is  displayed  if  the  enhanced 
communications test determines that the L-IP is operated behind a NAT router, but it has no 
NAT  address  configured.  In  this  case  go  to  the  IP  configuration  menu  and  configure  the 
correct NAT address or set it to Auto-NAT. 

Содержание L-IP














































































































































































Отзывы:

Нет отзывов