Lowrance GlobalMap 4000M Скачать руководство пользователя | Manualshive

Страница: 24 / 132

background image

18

Drill a 1-inch (25.4 mm) hole in the dash for the power and antenna
cables. The best location for this hole is immediately under the gimbal
bracket location. This way, the bracket can be installed so that it covers
the hole, holds the cables in position and results in a neat installation.
Some customers, however, prefer to mount the bracket to the side of the
cable hole — it's a matter of personal preference.

Front view (left) and side view (right) showing dimensions of the

GlobalMap 4800 when mounted on gimbal bracket.

After drilling the hole, pass the antenna connector

up

through the hole

from under the dash. Pass the power cable's bare-wire end

down

though the hole from the top.

If you wish, you can fill in the hole around the cables with a good marine
caulking compound. (Some marine dealers stock cable hole covers to con-
ceal the opening.) No matter what type of installation you prefer, be sure
to leave enough slack in the cables to allow tilting or swiveling the
GlobalMap 4800. If you choose to fill in the hole, be sure to position the
cables against the rear edge of the hole as you apply the fill material.

Before positioning the bracket, be sure to hold the cables against the
rear edge of the hole. Then, slide the bracket over the hole and butt the
rear of the bracket base firmly against the cables, thus pinning them in
place against the side of the hole. Finally, fasten the bracket to the
dash. Attach the unit to the gimbal bracket using the supplied gimbal
knobs and washers.

Millimeter

[Inch]

23.4
[0.92]

72.9
[2.87]

137.9
[5.43]

56.9
[2.24]

157.9
[6.22]

«
...
22
23
24
25
26
...
»

Содержание GlobalMap 4000M





































































































































Отзывы:

Нет отзывов

Похожие инструкции для GlobalMap 4000M

RoadMate Series

Бренд: Magellan Страницы: 14

RoadMate 1440 - Automotive GPS Receiver

Бренд: Magellan Страницы: 19

RoadMate 1200 - Automotive GPS Receiver

Бренд: Magellan Страницы: 31

RoadMate 1200 - Automotive GPS Receiver

Бренд: Magellan Страницы: 33

RoadMate 1200 - Automotive GPS Receiver

Бренд: Magellan Страницы: 8

Бренд: Garmin Страницы: 16

Бренд: Taimeta Страницы: 5

Бренд: Novatel Страницы: 8

DispoPilot.Guide

Бренд: FLEETBOARD Страницы: 32

Бренд: A-rival Страницы: 50

Touchscreen Navigation + Travel Guide Naviflash...

Бренд: naviflash Страницы: 2

Бренд: Garmin Страницы: 115

Бренд: CanMore Страницы: 7

Бренд: Garmin Страницы: 2

GPS 31 SL TracPak

Бренд: Garmin Страницы: 28

Бренд: RadarFind Страницы: 8

Бренд: Tait Страницы: 2

Бренд: Kingwo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды