Loop Telecom Loop-V 4200 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 107

background image

Chapter 5 Terminal Operation

5-7

5.5 System

Alarm

Setup

Press “M” to change and enable the alarm setup.

LOOP V4200-9 === System Alarm Setup === 09:25:55 07/19/2000
ARROW KEYS: CURSOR MOVE, TAB: ROLL OPTIONS

[Alarm Action]
ALARM : DISABLE
RELAY : DISABLE

[Alarm Type]
ALARM CUT OFF : DISABLE
PORT INACTIVE : DISABLE
PORT START-UP : DISABLE
CLK LOSS ALM : DISABLE

<< Press ESC key to return to previous menu >>

5.6 Firmware

Download

Press “L” to change the version of controller firmware. Move the cursor to "DOWNLOAD". The current
selection will be highlighted by an asterisk (*).

L O O P   V 4 2 0 0 - 9                       = = = D o w n l o a d / U p l o a d   F i r m w a r e   = = =             1 7 : 3 4 : 3 6   0 4 / 1 9 / 2 0 0 1




> >   S e l e c t   ?       * D O W N L O A D       U P L O A D

Press ENTER from the above screen. The following screen will show.

LOOP V4200-9 === Download Firmware === 09:25:55 07/19/2000
ARROW KEYS: CURSOR MOVE, Please Input: nnn.nnn.nnn.nnn, BACKSPACE to edit

Current Software Ver.: V1.18 02/04/1999
Current Firmware Bank: 2
NextBootFirmware Bank: 2
TFTP Server IP : 000.000.000.000
Firmware File Name :

<< Press ESC key to return to previous menu >>

«
...
63
64
65
66
67
...
»

Содержание Loop-V 4200












































































































Отзывы:

Нет отзывов

Похожие инструкции для Loop-V 4200

Бренд: Underhill Страницы: 30

Бренд: Wacker Neuson Страницы: 254

Бренд: Digitrax Страницы: 8

Бренд: Eminent Страницы: 31

Бренд: Linear Technology Страницы: 22

Бренд: Whistler Страницы: 2

Бренд: GME Страницы: 21

Бренд: T-TeleSec Страницы: 21

HDMI Super Booster Plus

Бренд: Gefen Страницы: 10

Бренд: Caen Страницы: 17

Бренд: I.D. AL Страницы: 26

Бренд: Fronius Страницы: 190

Бренд: Ace Plus Страницы: 9

PowerSourcePro REINVMA10

Бренд: ring Страницы: 122

Бренд: AGM Страницы: 71

Бренд: SOUNDMASTER Страницы: 16

Бренд: EASTMAN Страницы: 20

Бренд: Atlona Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды