Loongson 3A2000 Скачать руководство пользователя страница 60

Страница: 60 / 126

4/29/2020

Godson 3A2000 / 3B2000 Processor User Manual

twenty twoCoherent Mode

0x0

Determined by pin ICCC_EN

twenty oneNot Care Seqid

0x0

Does R / W don't care about HT order relationship

Not Axi2Seqid

0x1

Whether to convert the commands on the Axi bus to different SeqIDs,

If not converted, all read and write commands will use Fixed
Fixed ID number in Seqid

1: No conversion

0: conversion

19:16 Fixed Seqid

0x0

R / W When Not Axi2Seqid is valid, configure the

Seqid

15:12 Priority Nop

0x4

R / W HT bus Nop flow control packet priority

11: 8

Priority NPC

0x3

R / W Non Post channel read and write priority

7: 4

Priority RC

0x2

R / W Response channel reading and writing priority

3: 0

Priority PC

0x1

R / W

Post channel read and write priority
0x0: highest priority
0xF: lowest priority

The priority of each channel is changed according to time.

High priority strategy, the group register is used to configure each channel

'S initial priority

10.5.4

Receive diagnostic register

Offset: 0x54

Reset value: 0x00000000

Name: Receive diagnostic register

Table 10-14 Receive Diagnostic Register

Bit field

Bit field name

Bit width reset value Visit description

Sample_en

0x0

R / W

Enable cad and ctl for sampling input
0x0: prohibited
0x1: enable

15: 8

rx_ctl_catch

twenty four

0x0

R / W

Save the sampled input ctl
(0, 2, 4, 6) Four phases corresponding to CTL0 sampling
(1, 3, 5, 7) Four phases corresponding to CTL1 sampling

31:16 rx_cad_phase_0

twenty four

0x0

R / W save the input CAD [15: 0] value obtained by sampling

Page 75

Godson 3A2000 / 3B2000 Processor User Manual Part 1

10.5.5

Interrupt routing mode selection register

Offset: 0x58

Reset value: 0x00000000

Name: Interrupt routing mode selection register

Table 10-15 Interrupt Route Selection Register

Bit field

Bit field name

Bit width reset value Visit description

9: 8

ht_int_stripe

0x0

R / W

Corresponding to 3 interrupt routing methods, see 0 interrupt direction for specific description

Volume register

0x0: ht_int_stripe_1
0x1: ht_int_stripe_2
0x2: ht_int_stripe_4

10.5.6

Receive buffer initial register

Offset: 0x5c

Reset value: 0x07778888

Name: Receive buffer initialization configuration register

Содержание 3A2000































































































































Результаты поиска

Содержание 3A2000

Отзывы:

Loongson 3A2000, Руководство пользователя, Страница: 60 / 126

Результаты поиска

Содержание 3A2000

Отзывы: