LOGO SILVER ALLTRACK M3 Series Скачать руководство пользователя | Manualshive

Страница: 41 / 48

41

CLEANING

Regular care and maintenance will prevent premature wear and
unexpected damage to your LOGO SILVER product. Use only the
following cleaning methods.

!

WARNING

Cut all power to the wheelchair and always unplug the battery
charger before cleaning or disinfecting the wheelchair.

!

WARNING

Never hose off your power wheelchair or place it in direct contact
with water.

1. PAINT, METAL SURFACES AND PLASTICS

Clean with a soft cloth or sponge, using warm water and a
mild detergent on a monthly basis or when necessary. Wipe
down carefully and dry off. Protect the paint with a coat of
non-abrasive auto wax every 6 months.

!

WARNING

Do not use solvents or abrasive kitchen cleaners.

2. MOTORS

Clean around motor area weekly with a slightly damp (not
wet) cloth. Wipe off or blow away any fl uff, dust, or dirt on
or around the motors.

NOTE

- Applying grease or oil on any part of the power

wheelchair is not required except as specifi ed in this Owner's
Manual.

3. UPHOLSTERY, CLOTH AND FOAM

Hand-wash only using lukewarm water and a mild, non-
abrasive soap as needed. Before the surface dries, wipe off
any water or soapy water residues with a clean, dry cloth.
Repeat this procedure to remove stubborn dirt or stains. Drip-
dry only. See label instructions for information.

CAUTION!

- Machine washing or heat from a dryer may

damage fabric.

!

WARNING

Washing the fabric may decrease fi re-retardant properties.

4. WHEELCHAIR CONTROLLER

Should the control of your wheelchair become soiled or dirty,
it can be wiped with a damp cloth with a diluted disinfectant.

DISINFECTING & RE-USING

A POWER WHEELCHAIR

Many disinfecting products are commercially available and must
be used according to the manufacturer’s instructions. Before using
any products on the wheelchair, test on a small area to ensure the
disinfecting product is compatible with the wheelchair materials.

LOGO SILVER recommends using one of the following

solutions:

• (AHP) Accelerated Hydrogen Peroxide

disinfectant-based solution.

• Rapid alcohol-based solution
• Alkyl Dimethyl/Dimethyl ethyl benzyl ammonium

chlorides-based solution.

!

WARNING

Prior to the wheelchair being re-used (passing on to another
user), it must be carefully cleaned and disinfected. All surfaces
which come into contact with the user must be treated with a
disinfecting product.

CAUTION!

• Do not use solvents, bleaches, abrasives, synthetic detergents

or aerosols.

• Disinfectants may be used in dilution as specifi ed by the

manufacturer.

• Ensure surfaces are rinsed with clean water and dried

thoroughly.

• Always read the label on any commercial or domestic

cleaning substances.

• Always follow the instructions carefully.

!

WARNING

LOGO SILVER takes no responsibility for the effectiveness of the
disinfecting process, for contamination, cross infection or damage
to the product.

STORAGE TIPS

1. Store your power wheelchair in a clean, dry area. If you do

not, parts may rust or corrode.

2. Before using your power wheelchair, make sure it is in proper

working order. Inspect and service all items according to the
Maintenance Chart on

page 43.

3. If you store this power wheelchair for more than three

months, have it inspected by an authorized supplier

before use.

«
...
39
40
41
42
43
...
»

Содержание ALLTRACK M3 Series

















































Отзывы:

Нет отзывов

Похожие инструкции для ALLTRACK M3 Series

Бренд: Gate Страницы: 20

esprit action4 NG

Бренд: Invacare Страницы: 32

Бренд: C.T.M. Страницы: 20

Бренд: FreeWheel Страницы: 2

Бренд: 1800Wheelchair Страницы: 14

Бренд: chinesport Страницы: 8

Бренд: chinesport Страницы: 10

Бренд: Royale Страницы: 3

ErGo Selpro 1000

Бренд: RehabCare Страницы: 16

Бренд: Quickie Страницы: 120

Бренд: Quickie Страницы: 88

Бренд: Keizer Страницы: 26

R82 Multi Frame:x

Бренд: Etac Страницы: 101

Бренд: Otto Bock Страницы: 12

Бренд: Otto Bock Страницы: 24

Бренд: Otto Bock Страницы: 32

Бренд: Otto Bock Страницы: 36

Бренд: R Healthcare Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды