manualshive.com logo in svg

LOGO SILVER ALLTRACK M3 Series, Руководство пользователя

Поделиться
Скачать
LOGO SILVER ALLTRACK M3 Series Скачать руководство пользователя страница 10

10

POWER MODULE SETTINGS

 

! 

WARNING 

If your environment or your level of function and ability change, 
you may need to get the settings on your wheelchair’s power 
module adjusted. Your authorized supplier is best suited to adjust 
these settings. 

Contact your authorized supplier to adjust the power module 
settings immediately if you notice any change in your ability to:

•  Control the joystick
•  Hold your torso erect
•  Avoid running into objects.

EMI

 

! 

WARNING 

Read 

Section 

V

 on EMI on page 7, to reduce the risk of unin-

tended power wheelchair movement:

1.  NEVER turn on or use a hand-held transceiver while power 

to your wheelchair is on. Use extra care if you believe that 
such a device may be in use near your power wheelchair.

2.  Be aware of nearby radio or TV stations, and avoid coming 

close to them.

3.  If unintended movement occurs, turn your power wheelchair 

off as soon as it is safe. 

SAFETY CHECKLIST

 

! 

WARNING 

BEFORE EACH USE

1.   Make sure the power wheelchair operates smoothly. Check 

for noise, vibration, or a change in ease of use. (These may 
indicate low tire pressure, loose fasteners, or damage to your 
wheelchair).
•  If you detect a problem, make sure to repair or adjust the 

wheelchair. Your authorized supplier can help you find 
and correct the problem.

2.   Make sure batteries are charged. Green lights on charge 

indicator will light up when charge is full. Yellow lights 
indicate battery charge level is getting low. Red lights 
indicate batteries are in immediate need of charging.

3.   When not in use, keep your power wheelchair in a clean,  

dry place. 

CUSTOMIZATIONS, CHANGES  

 

 

& MODIFICATIONS 

 1 

PROHIBITED! 

NEVER make any customizations, changes or modifications to 
any part of your 

Alltrack 

power wheelchair unless explicitly 

authorized by 

LOGO SILVER.

 Doing so will void the warranty 

and may create a safety hazard.

 

! 

WARNING 

Adding accessories manufactured by any other third-party 
manufacturer without prior approval by 

LOGO SILVER

 will 

void the warranty and may create a safety hazard as these 
accessories haven’t been tested or approved by 

LOGO SILVER.

1.  Customizing, changing or modifying your 

Alltrack 

power 

wheelchair

 

may increase the risk of a fall or tip-over. 

2.  Modifications not authorized by 

LOGO SILVER

, constitute 

remanufacturing of the power wheelchair and will void the 
warranty. The user then assumes all future liability for the 
power wheelchair.

WHEN SEATED IN A PARKED  

 

 

POWER WHEELCHAIR

 

! 

WARNING 

1.   ALWAYS turn off all power to your wheelchair when you are 

parked, even for a moment. This will prevent:
•  Accidental movement from contact with the joystick by 

you or others.

•  Unintended movement from EMI sources.  

 

(See 

Section 

V

 page 7

).   

2.   Make sure that people who help you (for example, store 

clerks) are aware of the joystick and DO NOT touch it. If they 
do, your wheelchair may move suddenly when you do not 
expect it. 

Содержание ALLTRACK M3 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды