background image

USER MANUAL SMARTneo // 

PAGE 5

1.3 TRADEMARK 

Documentation can possibly also include representations of registered trademarks of goods or services as 
well as information on copyrighted or otherwise protected know-how of LOGICDATA or third parties. In all 
cases, all rights remain exclusively with the respective owner of the rights.

LOGICDATA® is a registered trademark of LOGICDATA Electronic und Software GmbH in the USA, the Eu-
ropean Union and other countries.

1.4  SYMBOLS AND SIGNAL WORDS USE

 

DANGER

Imminent threat to the lives of individuals

Warns against a dangerous situation. Failure to observe the war-
ning will result in death or severe personal injury.

WARNING

Risk of personal injury (serious injuries) and additional 
material damage

Warns against a dangerous situation. Failure to observe the war-
ning can result in severe personal injury.

CAUTION

Danger of material damage and additional low risk of injury

Warns against a dangerous situation. Failure to observe the war-
ning can result in injuries or material damage.

NOTICE

Notice that facilitates the handling or understanding of the  
product.

Damage from electrostatic discharge (ESD)

Содержание SMARTneo Series










































Отзывы: