LOFTNESS OS 170 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 76

background image

26

OS 170 Fertilizer Spreader OM

Set-up and Operation

Spread Pattern Adjustments (Cont’d)

Spinner RPM (Cont’d)

For Hydraulic Drive Spreaders

1

2

To make adjustments, use a hex key to turn the flow
control on the hydraulic valve located above the spinners.

Turn the adjustment screw (1) clockwise to decrease
RPM and counterclockwise to increase spinner RPM.

NOTE:

Do not make more than 1/4 turn of the adjustment
screw without rechecking the spinner RPM.

Recheck the spinner RPM using the tachometer or
spinner speed sensor on control display, if equipped.

When complete, tighten the lock nut (2) to maintain the
desired setting.

Spinner RPM (PTO Powered Spinners)

For PTO powered spinners, adjust tractor PTO speed. Or
if different spread width is desired, contact your dealer
for alternate pulleys.

Bander Operation

The optional bander at the rear of the spreader deflects
the fertilizer and places it in narrow zones or bands to
provide a concentrated application. Deflectors on the
bander can be adjusted to direct the fertilizer to the
desired location, or band width.

2

1

3

To adjust a deflector (1), loosen the handle (2) then raise
or lower the deflector angle to the desired setting.

Notches (3) are provided in the deflectors to be used as a
mark for equal setting on both bander deflectors.

Retighten handle when angle is set.

Repeat for opposite side.

NOTE:

Refer to “Bander Installation and Removal” on
page 32 for installation and removal of the
bander assembly. The bander will need to be
removed when broadcast spreading.

«
...
32
33
34
35
36
...
»

Содержание OS 170













































































Отзывы:

Нет отзывов

Похожие инструкции для OS 170

Бренд: IDTECH Страницы: 4

Бренд: Magtek Страницы: 2

Бренд: Velleman Страницы: 8

Бренд: Ikegami Страницы: 2

Бренд: H&S Страницы: 32

USB CompactFlash

Бренд: Memorex Страницы: 4

SecOVID Reader III

Бренд: Kobil Страницы: 20

Бренд: Roger Страницы: 23

Бренд: Magtek Страницы: 61

Бренд: Tar River Страницы: 32

Бренд: MAG Страницы: 2

Бренд: Salford Страницы: 31

Бренд: SealMaster Страницы: 29

Бренд: ICL Страницы: 12

Бренд: Vanderbilt Страницы: 43

Бренд: Vanderbilt Страницы: 76

Бренд: Manhattan Страницы: 12

Бренд: Magtek Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды