LOFTNESS OS 170 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 76

background image

25

OS 170 Fertilizer Spreader OM

Set-up and Operation

Spread Pattern Adjustments

Before attempting any spread pattern adjustments, make
sure the actual spread pattern has been determined.

Spinner Blade Positions

The spinner blades are the primary means of adjustment.

1

To adjust a spinner blade, remove the nut and washer (1)
from the bolt securing the blade to the spinner. Reposition
the blade and reinsert the bolt into the appropriate hole,
securing with washer and nut.

NOTE:

Any adjustment to a blade must also be
duplicated to the blade opposite the spinner
shaft. Also, spinner blade settings should be
identical to the opposite spinner.

Rear Deflector Adjustment

1

2

2

To adjust rear deflector (1), loosen the nut and washer (2)
on each side of deflector. Slide the deflector forward or
back accordingly. Retighten hardware when deflector is
in the desired position.

Spinner RPM

Check the spinner RPM with tractor throttle at operating
speed - “PTO speed” for PTO powered spinners. Hold
an electronic or mechanical tachometer near one of the
spinners to check the spinner speed.

NOTE:

For spreaders with spinner speed sensor, speed
can be checked from the controller.

Driving

Interval

(Spread

Width)

Spinner

Speed RPM

Pattern

Type

Spinner Blade

Setting

1

2

3

4

25 ft.

495

Pattern 1

Triangle

100%

Overlap

3

2

3

2

NOTE:

Spinner blade hole number increases as blade is moved

rearward. 1-2-3-4-5 when facing RH spinner; and 5-4-3-2-1

when facing LH spinner.

5

4

3

LH

Front of

Machine

RH

2

1

5 4

32

1

5 4 3 2 1

54

32

1

1

2

3

4

5

1 2

34

5

1 2 3 4 5

12

34

5

WARNING:

Spinners rotate at high speed.

Do not get hands or tachometer too close
when checking spinner RPM.

(Procedure continued on following page.)

«
...
31
32
33
34
35
...
»

Содержание OS 170













































































Отзывы:

Нет отзывов

Похожие инструкции для OS 170

Бренд: Ortus Страницы: 11

Бренд: Nedap Страницы: 21

Бренд: Hamlet Страницы: 4

FLEX-SELECT F130P Series

Бренд: Maruyama Страницы: 14

PSION WORKABOUT PRO

Бренд: TGM Страницы: 40

Бренд: Bluebird Страницы: 26

Бренд: SVT Страницы: 8

Бренд: Western Страницы: 24

Бренд: FAAC Страницы: 24

Бренд: SCM Microsystems Страницы: 59

Бренд: Kramer Страницы: 12

Бренд: Kramer Страницы: 17

Бренд: Caen RFID Страницы: 5

Бренд: Magtek Страницы: 26

Бренд: Rehau Страницы: 12

Бренд: Hama Страницы: 25

Бренд: Salto Страницы: 6

Бренд: EarthWay Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды