manualshive.com logo in svg

LocoCruiser LC201, Руководство пользователя

Поделиться
Скачать
LocoCruiser LC201 Скачать руководство пользователя страница 9

 

 

LocoCruiser  standard series  decoder user manual Ver1.0 

8 

No. 

Color 

Connect 

1 

Orange 

Motor + 

2 

Yellow 

Rear light - 

3 

Empty 

Empty 

4 

Black 

Left track 

5 

Gray 

Motor - 

6 

White 

Front light - 

7 

blue 

 pole 

8 

Red 

Right track 

 

   
4.4.1 Wiring Diagram for LocoCruiser LC201 

 

 
4.5 Locomotive with 6-pin DCC-standard Interface 

   Please check the wire colors are connected to the correct parts of the locomotive.   

 

Pin No. 

Colour 

Details 

1 

Orange 

Motor + 

2 

Yellow 

Rear Light - 

3 

Empty 

Empty 

4 

Black 

Left Rail 

5 

Gray 

Motor - 

6 

White 

Front light - 

7 

Blue 

Function  

8 

Red 

Right Rail 

 

After finishing  the installation, please check  the motor  and function wiring is completly 

insulated.    If not, the decoder could short out and burn out.    If this happens then the decoder 

will not be covered by warranty.   

Please be careful! 

 

 

 

Содержание LC201



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды